All

Refer to diagram for dimensions.

Thruster uses the same padded diamond surface as our Torker grip, but features a tall inside flange and thick molded end cap for a retro MX look and feel.

Features:

• Comes as a pair
• Injection-molded Thermoplastic Vulcanizate synthetic rubber is soft, durable and highly UV-resistant
• Thick one-piece molded end design for durability
• Tall inner flange protects your hands from discomfort against throttle and hand controls
• Safety wire grooves for added security
• Aftermarket throttle tube required to install Biltwell grips on stock H-D hand controls—see our Whiskey Throttle

Install Tips:

Counterintuitive though it might seem, aerosol WD-40 spray lubricant is our chemical of choice for installing Biltwell molded TPV grips. "But it's oil!" you say. Yes, but WD-40's combination of aerosol propellant and organic-based lubricant is perfect for sliding tight grips onto clean metal tubes. A quick 1 or 2-second blast into the open end of the grip is all it takes. Once installed, WD-40's chemical compound melts the grip interior just enough to make it stick to the bar like glue, without the mess. IMPORTANT: Wait 24 hours after installation before riding to give grips time to set up on the bars. Immediately after installation you can add safety wire wraps to both ends of the grips; this old motocross trick works great to reduce grip slip on the bars and throttle tube.

Refer to diagram for dimensions.

Thruster uses the same padded diamond surface as our Torker grip, but features a tall inside flange and thick molded end cap for a retro MX look and feel.

Features:

• Comes as a pair
• Injection-molded Thermoplastic Vulcanizate synthetic rubber is soft, durable and highly UV-resistant
• Thick one-piece molded end design for durability
• Tall inner flange protects your hands from discomfort against throttle and hand controls
• Safety wire grooves for added security
• Aftermarket throttle tube required to install Biltwell grips on stock H-D hand controls—see our Whiskey Throttle

Install Tips:

Counterintuitive though it might seem, aerosol WD-40 spray lubricant is our chemical of choice for installing Biltwell molded TPV grips. "But it's oil!" you say. Yes, but WD-40's combination of aerosol propellant and organic-based lubricant is perfect for sliding tight grips onto clean metal tubes. A quick 1 or 2-second blast into the open end of the grip is all it takes. Once installed, WD-40's chemical compound melts the grip interior just enough to make it stick to the bar like glue, without the mess. IMPORTANT: Wait 24 hours after installation before riding to give grips time to set up on the bars. Immediately after installation you can add safety wire wraps to both ends of the grips; this old motocross trick works great to reduce grip slip on the bars and throttle tube.

Refer to diagram for dimensions.

Thruster uses the same padded diamond surface as our Torker grip, but features a tall inside flange and thick molded end cap for a retro MX look and feel.

Features:

• Comes as a pair
• Injection-molded Thermoplastic Vulcanizate synthetic rubber is soft, durable and highly UV-resistant
• Thick one-piece molded end design for durability
• Tall inner flange protects your hands from discomfort against throttle and hand controls
• Safety wire grooves for added security
• Aftermarket throttle tube required to install Biltwell grips on stock H-D hand controls—see our Whiskey Throttle

Install Tips:

Counterintuitive though it might seem, aerosol WD-40 spray lubricant is our chemical of choice for installing Biltwell molded TPV grips. "But it's oil!" you say. Yes, but WD-40's combination of aerosol propellant and organic-based lubricant is perfect for sliding tight grips onto clean metal tubes. A quick 1 or 2-second blast into the open end of the grip is all it takes. Once installed, WD-40's chemical compound melts the grip interior just enough to make it stick to the bar like glue, without the mess. IMPORTANT: Wait 24 hours after installation before riding to give grips time to set up on the bars. Immediately after installation you can add safety wire wraps to both ends of the grips; this old motocross trick works great to reduce grip slip on the bars and throttle tube.

Refer to diagram for dimensions.

Diamond pillow surfacing is comfortable, but wears like the sole on a boot. No inside flange makes our Torker grip a great choice for aftermarket throttles—clean and lean.

Features:

• Comes as a pair
• Injection-molded Thermoplastic Vulcanizate synthetic rubber is soft, durable and highly UV-resistant
• Flangeless design looks great on café racers, vintage Japanese and British customs and modern cruisers
• Thick one-piece molded end design for durability
• Safety wire grooves for added security
• Aftermarket throttle tube required to install Biltwell grips on stock H-D hand controls—see our Whiskey Throttle

Install Tips:

Counterintuitive though it might seem, aerosol WD-40 spray lubricant is our chemical of choice for installing Biltwell molded TPV grips. "But it's oil!" you say. Yes, but WD-40's combination of aerosol propellant and organic-based lubricant is perfect for sliding tight grips onto clean metal tubes. A quick 1 or 2-second blast into the open end of the grip is all it takes. Once installed, WD-40's chemical compound melts the grip interior just enough to make it stick to the bar like glue, without the mess. IMPORTANT: Wait 24 hours after installation before riding to give grips time to set up on the bars. Immediately after installation you can add safety wire wraps to both ends of the grips; this old motocross trick works great to reduce grip slip on the bars and throttle tube.

Refer to diagram for dimensions.

Diamond pillow surfacing is comfortable, but wears like the sole on a boot. No inside flange makes our Torker grip a great choice for aftermarket throttles—clean and lean.

Features:

• Comes as a pair
• Injection-molded Thermoplastic Vulcanizate synthetic rubber is soft, durable and highly UV-resistant
• Flangeless design looks great on café racers, vintage Japanese and British customs and modern cruisers
• Thick one-piece molded end design for durability
• Safety wire grooves for added security
• Aftermarket throttle tube required to install Biltwell grips on stock H-D hand controls—see our Whiskey Throttle

Install Tips:

Counterintuitive though it might seem, aerosol WD-40 spray lubricant is our chemical of choice for installing Biltwell molded TPV grips. "But it's oil!" you say. Yes, but WD-40's combination of aerosol propellant and organic-based lubricant is perfect for sliding tight grips onto clean metal tubes. A quick 1 or 2-second blast into the open end of the grip is all it takes. Once installed, WD-40's chemical compound melts the grip interior just enough to make it stick to the bar like glue, without the mess. IMPORTANT: Wait 24 hours after installation before riding to give grips time to set up on the bars. Immediately after installation you can add safety wire wraps to both ends of the grips; this old motocross trick works great to reduce grip slip on the bars and throttle tube.

Refer to diagram for dimensions.

Diamond pillow surfacing is comfortable, but wears like the sole on a boot. No inside flange makes our Torker grip a great choice for aftermarket throttles—clean and lean.

Features:

• Comes as a pair
• Injection-molded Thermoplastic Vulcanizate synthetic rubber is soft, durable and highly UV-resistant
• Flangeless design looks great on café racers, vintage Japanese and British customs and modern cruisers
• Thick one-piece molded end design for durability
• Safety wire grooves for added security
• Aftermarket throttle tube required to install Biltwell grips on stock H-D hand controls—see our Whiskey Throttle

Install Tips:

Counterintuitive though it might seem, aerosol WD-40 spray lubricant is our chemical of choice for installing Biltwell molded TPV grips. "But it's oil!" you say. Yes, but WD-40's combination of aerosol propellant and organic-based lubricant is perfect for sliding tight grips onto clean metal tubes. A quick 1 or 2-second blast into the open end of the grip is all it takes. Once installed, WD-40's chemical compound melts the grip interior just enough to make it stick to the bar like glue, without the mess. IMPORTANT: Wait 24 hours after installation before riding to give grips time to set up on the bars. Immediately after installation you can add safety wire wraps to both ends of the grips; this old motocross trick works great to reduce grip slip on the bars and throttle tube.

Refer to diagram for dimensions.

Diamond pillow surfacing is comfortable, but wears like the sole on a boot. No inside flange makes our Torker grip a great choice for aftermarket throttles—clean and lean.

Features:

• Comes as a pair
• Injection-molded Thermoplastic Vulcanizate synthetic rubber is soft, durable and highly UV-resistant
• Flangeless design looks great on café racers, vintage Japanese and British customs and modern cruisers
• Thick one-piece molded end design for durability
• Safety wire grooves for added security
• Aftermarket throttle tube required to install Biltwell grips on stock H-D hand controls—see our Whiskey Throttle

Install Tips:

Counterintuitive though it might seem, aerosol WD-40 spray lubricant is our chemical of choice for installing Biltwell molded TPV grips. "But it's oil!" you say. Yes, but WD-40's combination of aerosol propellant and organic-based lubricant is perfect for sliding tight grips onto clean metal tubes. A quick 1 or 2-second blast into the open end of the grip is all it takes. Once installed, WD-40's chemical compound melts the grip interior just enough to make it stick to the bar like glue, without the mess. IMPORTANT: Wait 24 hours after installation before riding to give grips time to set up on the bars. Immediately after installation you can add safety wire wraps to both ends of the grips; this old motocross trick works great to reduce grip slip on the bars and throttle tube.

Refer to diagram for dimensions.

Diamond pillow surfacing is comfortable, but wears like the sole on a boot. No inside flange makes our Torker grip a great choice for aftermarket throttles—clean and lean.

Features:

• Comes as a pair
• Injection-molded Thermoplastic Vulcanizate synthetic rubber is soft, durable and highly UV-resistant
• Flangeless design looks great on café racers, vintage Japanese and British customs and modern cruisers
• Thick one-piece molded end design for durability
• Safety wire grooves for added security
• Aftermarket throttle tube required to install Biltwell grips on stock H-D hand controls—see our Whiskey Throttle

Install Tips:

Counterintuitive though it might seem, aerosol WD-40 spray lubricant is our chemical of choice for installing Biltwell molded TPV grips. "But it's oil!" you say. Yes, but WD-40's combination of aerosol propellant and organic-based lubricant is perfect for sliding tight grips onto clean metal tubes. A quick 1 or 2-second blast into the open end of the grip is all it takes. Once installed, WD-40's chemical compound melts the grip interior just enough to make it stick to the bar like glue, without the mess. IMPORTANT: Wait 24 hours after installation before riding to give grips time to set up on the bars. Immediately after installation you can add safety wire wraps to both ends of the grips; this old motocross trick works great to reduce grip slip on the bars and throttle tube.

1" O.D, Smooth for custom applications - these have no slots, dimples or castellated ends. We have TBW versions available also.

Refer to diagram for dimensions.

The top-selling handlebar in our range, and for good reason. Our Tracker bars come in two O.D.'s and three heights, and look great in any stock or aftermarket riser you can imagine. These handlebars are constructed with seamless CNC mandrel bent 0.120” wall 4130 chromoly tubes. Available in two styles: Smooth bars are for custom applications and have no slots, dimples or castellated ends. TBW w/ insert handlebars work with regular, cable-operated throttles, and if you remove the black end plug it will accept Harley's Throttle-By-Wire control module. These bars have slots on each side for stock H-D hand controls and an exit slot in the center for internal wiring.

Features:

• Seamless 0.120" (3mm) wall 4130 chromoly construction
• Precision mandrel-bent tubing for comfortable, precise ergonomics
• Black electroplate and mirror chrome-plated finishes available
• 1" O.D (7/8" option available), 18.4mm I.D
• 1" O.D. model available in smooth for custom application or TBW w/ insert for regular, cable-operated throttles, and if you remove the black end plug it will accept Harley's Throttle-By-Wire control module
• Technischer Überwachungsverein (Technical Inspection Association, or TüV) in Germany is an independent laboratory that tests the fatigue strength, manufacturing quality, and fitment for a wide range of consumer products, with special emphasis on automotive and motorcycle components and accessories. Biltwell handlebars and risers that have received TüV verification are among the strongest and most thoroughly well-tested motorcycle parts in the world.

Form & Function:

With a backsweep less severe than most stock handlebars, any Tracker in our range is a great replacement for riders who want to ditch the wheelbarrow feel of OE bars. When people ask for our advice on which Tracker to mate with any given Murdock riser, we recommend building a combo that puts your hands slightly below or even with the height of your shoulders when you're sitting comfortably on your motorcycle. Hands higher than shoulder height is popular, but it's a position better suited for experienced riders. If the cables and control wires on your bike prohibit going too tall or wide with your bars, combine our low or mid Tracker with some Slimline or Thunder risers for a clean, race-inspired, comfortable cockpit.

7/8" O.D, Smooth for custom applications - these have no slots, dimples or castellated ends.

Refer to diagram for dimensions.

The top-selling handlebar in our range, and for good reason. Our Tracker bars come in two O.D.'s and three heights, and look great in any stock or aftermarket riser you can imagine. 4130 chromoly construction, chrome or black electroplated finish for looks and durability.

Features:

• Seamless 0.120" (3mm) wall 4130 chromoly construction
• Precision mandrel-bent tubing for comfortable, precise ergonomics
• Black electroplate and mirror chrome-plated finishes available
• Two sizes available: 7/8" and 1" O.D.
• 7/8" O.D. with a 16.2mm I.D. model available in smooth for aftermarket levers 
• Technischer Überwachungsverein (Technical Inspection Association, or TüV) in Germany is an independent laboratory that tests the fatigue strength, manufacturing quality, and fitment for a wide range of consumer products, with special emphasis on automotive and motorcycle components and accessories. Biltwell handlebars and risers that have received TüV verification are among the strongest and most thoroughly well-tested motorcycle parts in the world.

Form & Function:

With a backsweep less severe than most stock handlebars, any Tracker in our range is a great replacement for riders who want to ditch the wheelbarrow feel of OE bars. When people ask for our advice on which Tracker to mate with any given Murdock riser, we recommend building a combo that puts your hands slightly below or even with the height of your shoulders when you're sitting comfortably on your motorcycle. Hands higher than shoulder height is popular, but it's a position better suited for experienced riders. If the cables and control wires on your bike prohibit going too tall or wide with your bars, combine our low or mid Tracker with some Slimline or Thunder risers for a clean, race-inspired, comfortable cockpit.

7/8" O.D, Smooth for custom applications - these have no slots, dimples or castellated ends.

Refer to diagram for dimensions.

The top-selling handlebar in our range, and for good reason. Our Tracker bars come in two O.D.'s and three heights, and look great in any stock or aftermarket riser you can imagine. 4130 chromoly construction, chrome or black electroplated finish for looks and durability.

Features:

• Seamless 0.120" (3mm) wall 4130 chromoly construction
• Precision mandrel-bent tubing for comfortable, precise ergonomics
• Black electroplate and mirror chrome-plated finishes available
• Two sizes available: 7/8" and 1" O.D.
• 7/8" O.D. with a 16.2mm I.D. model available in smooth for aftermarket levers 
• Technischer Überwachungsverein (Technical Inspection Association, or TüV) in Germany is an independent laboratory that tests the fatigue strength, manufacturing quality, and fitment for a wide range of consumer products, with special emphasis on automotive and motorcycle components and accessories. Biltwell handlebars and risers that have received TüV verification are among the strongest and most thoroughly well-tested motorcycle parts in the world.

Form & Function:

With a backsweep less severe than most stock handlebars, any Tracker in our range is a great replacement for riders who want to ditch the wheelbarrow feel of OE bars. When people ask for our advice on which Tracker to mate with any given Murdock riser, we recommend building a combo that puts your hands slightly below or even with the height of your shoulders when you're sitting comfortably on your motorcycle. Hands higher than shoulder height is popular, but it's a position better suited for experienced riders. If the cables and control wires on your bike prohibit going too tall or wide with your bars, combine our low or mid Tracker with some Slimline or Thunder risers for a clean, race-inspired, comfortable cockpit.

1" O.D, TBW Version w/ insert - work with regular, cable-operated throttles, and if you remove the black end plug it will accept Harley's Throttle-By-Wire control module. These bars have slots on each side for stock H-D hand controls and an exit slot in the center for internal wiring. We also have Smooth options available for custom applications.

Refer to diagram for dimensions.

The top-selling handlebar in our range, and for good reason. Our Tracker bars come in two O.D.'s and three heights, and look great in any stock or aftermarket riser you can imagine. These handlebars are constructed with seamless CNC mandrel bent 0.120” wall 4130 chromoly tubes. Available in two styles: Smooth bars are for custom applications and have no slots, dimples or castellated ends. TBW w/ insert handlebars work with regular, cable-operated throttles, and if you remove the black end plug it will accept Harley's Throttle-By-Wire control module. These bars have slots on each side for stock H-D hand controls and an exit slot in the center for internal wiring.

Features:

• Seamless 0.120" (3mm) wall 4130 chromoly construction
• Precision mandrel-bent tubing for comfortable, precise ergonomics
• Black electroplate finish
• TBW w/ insert option has a 1in O.D. with a 20.9mm I.D.
• 1" O.D. model available in smooth for custom application or TBW w/ insert for regular, cable-operated throttles, and if you remove the black end plug it will accept Harley's Throttle-By-Wire control module
• Technischer Überwachungsverein (Technical Inspection Association, or TüV) in Germany is an independent laboratory that tests the fatigue strength, manufacturing quality, and fitment for a wide range of consumer products, with special emphasis on automotive and motorcycle components and accessories. Biltwell handlebars and risers that have received TüV verification are among the strongest and most thoroughly well-tested motorcycle parts in the world.

Form & Function:

With a backsweep less severe than most stock handlebars, any Tracker in our range is a great replacement for riders who want to ditch the wheelbarrow feel of OE bars. When people ask for our advice on which Tracker to mate with any given Murdock riser, we recommend building a combo that puts your hands slightly below or even with the height of your shoulders when you're sitting comfortably on your motorcycle. Hands higher than shoulder height is popular, but it's a position better suited for experienced riders. If the cables and control wires on your bike prohibit going too tall or wide with your bars, combine our low or mid Tracker with some Slimline or Thunder risers for a clean, race-inspired, comfortable cockpit.

7/8" O.D, Smooth for custom applications - these have no slots, dimples or castellated ends.

Refer to diagram for dimensions.

The top-selling handlebar in our range, and for good reason. Our Tracker bars come in two O.D.'s and three heights, and look great in any stock or aftermarket riser you can imagine. 4130 chromoly construction, chrome or black electroplated finish for looks and durability.

Features:

• Seamless 0.120" (3mm) wall 4130 chromoly construction
• Precision mandrel-bent tubing for comfortable, precise ergonomics
• Black electroplate and mirror chrome-plated finishes available
• Two sizes available: 7/8" and 1" O.D.
• 7/8" O.D. with a 16.2mm I.D. model available in smooth for aftermarket levers 
• Technischer Überwachungsverein (Technical Inspection Association, or TüV) in Germany is an independent laboratory that tests the fatigue strength, manufacturing quality, and fitment for a wide range of consumer products, with special emphasis on automotive and motorcycle components and accessories. Biltwell handlebars and risers that have received TüV verification are among the strongest and most thoroughly well-tested motorcycle parts in the world.

Form & Function:

With a backsweep less severe than most stock handlebars, any Tracker in our range is a great replacement for riders who want to ditch the wheelbarrow feel of OE bars. When people ask for our advice on which Tracker to mate with any given Murdock riser, we recommend building a combo that puts your hands slightly below or even with the height of your shoulders when you're sitting comfortably on your motorcycle. Hands higher than shoulder height is popular, but it's a position better suited for experienced riders. If the cables and control wires on your bike prohibit going too tall or wide with your bars, combine our low or mid Tracker with some Slimline or Thunder risers for a clean, race-inspired, comfortable cockpit.

7/8" O.D, Smooth for custom applications - these have no slots, dimples or castellated ends.

Refer to diagram for dimensions.

The top-selling handlebar in our range, and for good reason. Our Tracker bars come in two O.D.'s and three heights, and look great in any stock or aftermarket riser you can imagine. 4130 chromoly construction, chrome or black electroplated finish for looks and durability.

Features:

• Seamless 0.120" (3mm) wall 4130 chromoly construction
• Precision mandrel-bent tubing for comfortable, precise ergonomics
• Black electroplate and mirror chrome-plated finishes available
• Two sizes available: 7/8" and 1" O.D.
• 7/8" O.D. with a 16.2mm I.D. model available in smooth for aftermarket levers 
• Technischer Überwachungsverein (Technical Inspection Association, or TüV) in Germany is an independent laboratory that tests the fatigue strength, manufacturing quality, and fitment for a wide range of consumer products, with special emphasis on automotive and motorcycle components and accessories. Biltwell handlebars and risers that have received TüV verification are among the strongest and most thoroughly well-tested motorcycle parts in the world.

Form & Function:

With a backsweep less severe than most stock handlebars, any Tracker in our range is a great replacement for riders who want to ditch the wheelbarrow feel of OE bars. When people ask for our advice on which Tracker to mate with any given Murdock riser, we recommend building a combo that puts your hands slightly below or even with the height of your shoulders when you're sitting comfortably on your motorcycle. Hands higher than shoulder height is popular, but it's a position better suited for experienced riders. If the cables and control wires on your bike prohibit going too tall or wide with your bars, combine our low or mid Tracker with some Slimline or Thunder risers for a clean, race-inspired, comfortable cockpit.

1" O.D, Smooth for custom applications - these have no slots, dimples or castellated ends. We have TBW versions available also.

Refer to diagram for dimensions.

The top-selling handlebar in our range, and for good reason. Our Tracker bars come in two O.D.'s and three heights, and look great in any stock or aftermarket riser you can imagine. These handlebars are constructed with seamless CNC mandrel bent 0.120” wall 4130 chromoly tubes. Available in two styles: Smooth bars are for custom applications and have no slots, dimples or castellated ends. TBW w/ insert handlebars work with regular, cable-operated throttles, and if you remove the black end plug it will accept Harley's Throttle-By-Wire control module. These bars have slots on each side for stock H-D hand controls and an exit slot in the center for internal wiring.

Features:

• Seamless 0.120" (3mm) wall 4130 chromoly construction
• Precision mandrel-bent tubing for comfortable, precise ergonomics
• Black electroplate finish
• 1" O.D (7/8" option available), 18.4mm I.D
• 1" O.D. model available in smooth for custom application or TBW w/ insert for regular, cable-operated throttles, and if you remove the black end plug it will accept Harley's Throttle-By-Wire control module
• Technischer Überwachungsverein (Technical Inspection Association, or TüV) in Germany is an independent laboratory that tests the fatigue strength, manufacturing quality, and fitment for a wide range of consumer products, with special emphasis on automotive and motorcycle components and accessories. Biltwell handlebars and risers that have received TüV verification are among the strongest and most thoroughly well-tested motorcycle parts in the world.

Form & Function:

With a backsweep less severe than most stock handlebars, any Tracker in our range is a great replacement for riders who want to ditch the wheelbarrow feel of OE bars. When people ask for our advice on which Tracker to mate with any given Murdock riser, we recommend building a combo that puts your hands slightly below or even with the height of your shoulders when you're sitting comfortably on your motorcycle. Hands higher than shoulder height is popular, but it's a position better suited for experienced riders. If the cables and control wires on your bike prohibit going too tall or wide with your bars, combine our low or mid Tracker with some Slimline or Thunder risers for a clean, race-inspired, comfortable cockpit.

1" O.D, TBW Version w/ insert - work with regular, cable-operated throttles, and if you remove the black end plug it will accept Harley's Throttle-By-Wire control module. These bars have slots on each side for stock H-D hand controls and an exit slot in the center for internal wiring. We also have Smooth options available for custom applications.

Refer to diagram for dimensions.

The top-selling handlebar in our range, and for good reason. Our Tracker bars come in two O.D.'s and three heights, and look great in any stock or aftermarket riser you can imagine. These handlebars are constructed with seamless CNC mandrel bent 0.120” wall 4130 chromoly tubes. Available in two styles: Smooth bars are for custom applications and have no slots, dimples or castellated ends. TBW w/ insert handlebars work with regular, cable-operated throttles, and if you remove the black end plug it will accept Harley's Throttle-By-Wire control module. These bars have slots on each side for stock H-D hand controls and an exit slot in the center for internal wiring.

Features:

• Seamless 0.120" (3mm) wall 4130 chromoly construction
• Precision mandrel-bent tubing for comfortable, precise ergonomics
• Black electroplate finish
• TBW w/ insert option has a 1in O.D. with a 20.9mm I.D.
• 1" O.D. model available in smooth for custom application or TBW w/ insert for regular, cable-operated throttles, and if you remove the black end plug it will accept Harley's Throttle-By-Wire control module
• Technischer Überwachungsverein (Technical Inspection Association, or TüV) in Germany is an independent laboratory that tests the fatigue strength, manufacturing quality, and fitment for a wide range of consumer products, with special emphasis on automotive and motorcycle components and accessories. Biltwell handlebars and risers that have received TüV verification are among the strongest and most thoroughly well-tested motorcycle parts in the world.

Form & Function:

With a backsweep less severe than most stock handlebars, any Tracker in our range is a great replacement for riders who want to ditch the wheelbarrow feel of OE bars. When people ask for our advice on which Tracker to mate with any given Murdock riser, we recommend building a combo that puts your hands slightly below or even with the height of your shoulders when you're sitting comfortably on your motorcycle. Hands higher than shoulder height is popular, but it's a position better suited for experienced riders. If the cables and control wires on your bike prohibit going too tall or wide with your bars, combine our low or mid Tracker with some Slimline or Thunder risers for a clean, race-inspired, comfortable cockpit.

7/8" O.D, Smooth for custom applications - these have no slots, dimples or castellated ends.

Refer to diagram for dimensions.

The top-selling handlebar in our range, and for good reason. Our Tracker bars come in two O.D.'s and three heights, and look great in any stock or aftermarket riser you can imagine. 4130 chromoly construction, chrome or black electroplated finish for looks and durability.

Features:

• Seamless 0.120" (3mm) wall 4130 chromoly construction
• Precision mandrel-bent tubing for comfortable, precise ergonomics
• Black electroplate and mirror chrome-plated finishes available
• Two sizes available: 7/8" and 1" O.D.
• 7/8" O.D. with a 16.2mm I.D. model available in smooth for aftermarket levers 
• Technischer Überwachungsverein (Technical Inspection Association, or TüV) in Germany is an independent laboratory that tests the fatigue strength, manufacturing quality, and fitment for a wide range of consumer products, with special emphasis on automotive and motorcycle components and accessories. Biltwell handlebars and risers that have received TüV verification are among the strongest and most thoroughly well-tested motorcycle parts in the world.

Form & Function:

With a backsweep less severe than most stock handlebars, any Tracker in our range is a great replacement for riders who want to ditch the wheelbarrow feel of OE bars. When people ask for our advice on which Tracker to mate with any given Murdock riser, we recommend building a combo that puts your hands slightly below or even with the height of your shoulders when you're sitting comfortably on your motorcycle. Hands higher than shoulder height is popular, but it's a position better suited for experienced riders. If the cables and control wires on your bike prohibit going too tall or wide with your bars, combine our low or mid Tracker with some Slimline or Thunder risers for a clean, race-inspired, comfortable cockpit.

7/8" O.D, Smooth for custom applications - these have no slots, dimples or castellated ends.

Refer to diagram for dimensions.

The top-selling handlebar in our range, and for good reason. Our Tracker bars come in two O.D.'s and three heights, and look great in any stock or aftermarket riser you can imagine. 4130 chromoly construction, chrome or black electroplated finish for looks and durability.

Features:

• Seamless 0.120" (3mm) wall 4130 chromoly construction
• Precision mandrel-bent tubing for comfortable, precise ergonomics
• Black electroplate and mirror chrome-plated finishes available
• Two sizes available: 7/8" and 1" O.D.
• 7/8" O.D. with a 16.2mm I.D. model available in smooth for aftermarket levers 
• Technischer Überwachungsverein (Technical Inspection Association, or TüV) in Germany is an independent laboratory that tests the fatigue strength, manufacturing quality, and fitment for a wide range of consumer products, with special emphasis on automotive and motorcycle components and accessories. Biltwell handlebars and risers that have received TüV verification are among the strongest and most thoroughly well-tested motorcycle parts in the world.

Form & Function:

With a backsweep less severe than most stock handlebars, any Tracker in our range is a great replacement for riders who want to ditch the wheelbarrow feel of OE bars. When people ask for our advice on which Tracker to mate with any given Murdock riser, we recommend building a combo that puts your hands slightly below or even with the height of your shoulders when you're sitting comfortably on your motorcycle. Hands higher than shoulder height is popular, but it's a position better suited for experienced riders. If the cables and control wires on your bike prohibit going too tall or wide with your bars, combine our low or mid Tracker with some Slimline or Thunder risers for a clean, race-inspired, comfortable cockpit.

Made in Utah, USA by our friends at Voile® these 20” (0.50m) long straps are made of tough stretch polyurethane, with a UV-resistant additive to increase their lifespan. Immensely versatile, these personal favorites of ours are perfect for securing gear on any motorcycle in any weather.

Features:

• Usable Length Range: 5.1in — 17.1in / 13cm — 43.5cm
• Material: UV-Resistant Polyurethane
• Buckle: Super Tough Nylon
• Non-Marring
• Non-Conductive
• Won't Slip
• Holds Tight
• Super Strong
• UV Resistant
• Works in Extreme Weather
• Daisy Chain Together
• Time-Tested Design
• Comes as 1 single strap

Form & Function:

These Voile Straps® are made of the same tough stretch polyurethane, including the UV-resistant additive that increases their lifespan. Their heavy-duty heat-treated aluminum buckle features a slim profile for packing efficiency and extra durability. These straps are the definitive way to secure your gear, so toss those cheesy bungee cords!

Made in Utah, USA by our friends at Voile® these 32” (0.80m) long straps are 20% thicker and 25% wider, making them the strongest of their kind. Immensely versatile, these personal favorites of ours are perfect for securing gear on any motorcycle in any weather.

Features:

• Usable Length Range: 8.8in — 28.7in / 22.2cm — 72.9cm
• Material: UV-Resistant Polyurethane
• Buckle: Hardened Aluminum
• 20% Thicker
• 25% Wider
• Extra Long
• Won't Slip
• Holds Tight
• Super Strong
• UV Resistant
• Works in Extreme Weather
• Daisy Chain Together
• Time-Tested Design
• Comes as 1 single strap

Form & Function:

These Voile Straps® are made of the same tough stretch polyurethane, including the UV-resistant additive that increases their lifespan. Their heavy-duty heat-treated aluminum buckle features a slim profile for packing efficiency and extra durability. These straps are the definitive way to secure your gear, so toss those cheesy bungee cords!

Stock Harley grips are molded to a flexible plastic tube inside the hand control, and don't provide the precision feel befitting a custom motorcycle. Our CNC-machined aluminum throttle tube replaces the stock unit to improve performance and make grip installation easy.

Features:

• CNC-machined 6061 T-6 aluminum construction
• Fits 1-inch O.D. handlebars, accepts dual-cable throttle assemblies
• Knurled alloy tube accepts aftermarket rubber grips
• Black electroplate or clear anodized over raw aluminum finish
• Retrofits to many model-year stock and select aftermarket H-D hand controls
• This component required to install Biltwell molded TPV grips

Form & Function:

Stock Harley grips aren't much to brag about: hard as a brick, slippery as a frog and ugly as a mud piñata. Our Whiskey Throttle tube lets you ditch stock grips so you can install comfortable molded rubber grips on your freedom machine. Our Whiskey throttle tube and a pair of Biltwell grips is one of the fastest, least expensive performance upgrades you can do on your motorcycle.

Stock Harley grips are molded to a flexible plastic tube inside the hand control, and don't provide the precision feel befitting a custom motorcycle. Our CNC-machined aluminum throttle tube replaces the stock unit to improve performance and make grip installation easy.

Features:

• CNC-machined 6061 T-6 aluminum construction
• Fits 1-inch O.D. handlebars, accepts dual-cable throttle assemblies
• Knurled alloy tube accepts aftermarket rubber grips
• Black electroplate or clear anodized over raw aluminum finish
• Retrofits to many model-year stock and select aftermarket H-D hand controls
• This component required to install Biltwell molded TPV grips

Form & Function:

Stock Harley grips aren't much to brag about: hard as a brick, slippery as a frog and ugly as a mud piñata. Our Whiskey Throttle tube lets you ditch stock grips so you can install comfortable molded rubber grips on your freedom machine. Our Whiskey throttle tube and a pair of Biltwell grips is one of the fastest, least expensive performance upgrades you can do on your motorcycle.

The original Biltwell Work glove has been a rugged staple in our motorcycle gear line for years. Work 2.0 raises the bar for style and construction with an elasticated cuff, suede cowhide palm protection, and 100% goatskin construction for more comfort and dexterity.

Features:

• 100% goatskin construction
• Suede cow leather palm panels for improved grip and abrasion resistance
• Elasticated wrist closure on full wraparound cuffs
• Super durable polyester thread throughout
• Wrist cuff features suede pull with embroidered logo detailing
• Quilted expansion panels on index and middle finger joints for added dexterity
• Innovative palm, thumb and finger construction puts seams on the outside—less chafing, more comfort
• Raised welt detailing on back of hand
• Available in S-XXL sizes
• Black and Gold colorways available

Form & Function:

Known by many names—workers, ropers, truckers—this style of glove gained early popularity among folks who earn a living with their hands. That blue-collar street cred is what made our original Work glove so popular with modern motorcyclers. Less flash, more function and comfort. Work Glove 2.0 builds on our original model’s strengths by replacing the cowhide with soft, supple goatskin leather. All other design and construction features remain to give you moto-tested comfort and performance.

Don’t be caught looking downtrodden or homeless in a nagged out knit cap. Get back in the groove with a stylish beanie from your friends at Biltwell.

Our Bolts logo woven in dark grey over black. Tight weave with just the right elasticity for a comfortable fit, one-size-fits-all stretchiness, and colorfast synthetic blend construction for durability.

If you’ve ever worked on your own motorcycle, you know this anxiety!

Our talented friend @almost_cesar in Switzerland captured that moment when the rider realizes he failed to tighten the axle and things are going bad in a hurry.

7.5oz. ring spun cotton makes for a super-comfortable, lightweight hoodie.

The thumbholes in the cuffs are great for keeping your sleeves up while riding the wild thunder.

Printed here in Temecula, CA USA.

A T-SHIRT DESIGNED TO PROVIDE STYLE AND QUICK-DRYING COMFORT

The Blinders Tech Tee is the ultimate combination of performance and casual comfort. The drirelease® fabric wick sweat away from the body and dries 4X faster than traditional cotton and features odor protection which lasts the lifetime of the tee.

• Rapidly wicks perspiration
• Dries 4x faster than cotton
• Odor guard keeps you fresh
• Performance benefits last for lifetime of the garment
• Premium fit

LIGHTWEIGHT STRETCH FLANNEL FOR EXTRA COMFORT AND MOBILITY

The Boedi Flannel features superior comfort and performance-ready mobility thanks to a lightweight and flexible fabrication.

• Stretch for extra comfort and mobility
• Exterior woven label at bottom front
• Fox Racing flag label at chest pocket
• Fox logo buttons

 

LIGHTWEIGHT STRETCH FLANNEL FOR EXTRA COMFORT AND MOBILITY 

The Boedi Flannel features superior comfort and performance-ready mobility thanks to a lightweight and flexible fabrication.

• Stretch for extra comfort and mobility
• Exterior woven label at bottom front
• Fox Racing flag label at chest pocket
• Fox logo buttons






 
•  
•  
•  
•  

BS SLA Factory Activated batteries have all the features of Maintenance Free batteries with the increased power of a radial grid design and additional plates.

These batteries are prefectly suitable for motorcycles, scooters, ATV's, UTV's, watercraft, and lawnmowers.

Features:

• Wet charged factory activated and ready to go
• Higher life cycle (up to three times longer than conventional batteries)
• Easy to install (no risk of spilling acid)
• Plate sulfation minimized
• AGM construction (absorbed acid)
• VRLA battery (Valve Regulated Lead Acid)
• Sealed, no gas emission through venting hole (under normal operation)
• Increased power and extended life
• Extreme vibration resistance

Find the correct fitment for your motorcycle here: BS Battery Fitment Guide

BSLi battery is a part of our LiFePO4 range. Designed for the most demanding riders, the battery offers maximum starting performance, further safety and higher cycle life.
With its ultra-lightweight design, the battery provides faster acceleration to all powersport vehicles.

Useful, this battery is equipped with a voltage indicator to check the state of charge at any time.

FEATURES

• Ready to use
• Lighter weight – up to 70% than lead acid batteries
• Multi-positioning mounting – up to 180°
• Extensive cycle life – over 2000 cycles
• Fast charging
• Very safe and environmental friendly
• Very low self discharge
• Can start engines after a long period of storage
• Robust brass terminals
• Heat temperature resistance up to 230 °C
• Waterproof design
• Spacers to adjust the dimensions if necessary, to make sure new battery can be installed firmly in the battery box

UPGRADE FROM:

Find the correct fitment for your motorcycle here: BS Battery Fitment Guide