BILTWELL

Refer to diagram for dimensions.

The Moto Grip’s design allows it to be mounted with more aggressive traction on top or bottom depending on the rider’s preference. Kraton Rubber in the Soft compound offers slightly more cushion and tackiness than the Medium compound.

Features:

• Comes as a pair
• Injection-molded Kraton rubber is soft, comfortable and highly UV-resistant
• Available in two sizes and two compounds: 1-inch or 7/8-inch
• Available in two compounds medium for more durability with a longer lifespan or soft for more comfort and grip
• Tall inside flange cushions rider's hands from rubbing the throttle and controls
• Safety wire grooves for added security
• Designed to install on bikes that use a throttle tube - not included

Install Tips:

Counterintuitive though it might seem, aerosol WD-40 spray lubricant is our chemical of choice for installing Biltwell molded Krayton grips. "But it's oil!" you say. Yes, but WD-40's combination of aerosol propellant and organic-based lubricant is perfect for sliding tight grips onto clean metal tubes. A quick 1- or 2-second blast into the open end of the grip is all it takes. Once installed, WD-40's chemical compound melts the grip interior just enough to make it stick to the bar like glue, without the mess. IMPORTANT: Wait 24 hours after installation before riding to give grips time to set up on the bars. Immediately after installation you can add safety wire wraps to both ends of the grips; this old motocross trick works great to reduce grip slip on the bars and throttle tube.

Refer to diagram for dimensions.

The Moto Grip’s design allows it to be mounted with more aggressive traction on top or bottom depending on the rider’s preference. Kraton Rubber in the Soft compound offers slightly more cushion and tackiness than the Medium compound.

Features:

• Comes as a pair
• Injection-molded Kraton rubber is soft, comfortable and highly UV-resistant
• Available in two sizes and two compounds: 1-inch or 7/8-inch
• Available in two compounds medium for more durability with a longer lifespan or soft for more comfort and grip
• Tall inside flange cushions rider's hands from rubbing the throttle and controls
• Safety wire grooves for added security
• Designed to install on bikes that use a throttle tube - not included

Install Tips:

Counterintuitive though it might seem, aerosol WD-40 spray lubricant is our chemical of choice for installing Biltwell molded Krayton grips. "But it's oil!" you say. Yes, but WD-40's combination of aerosol propellant and organic-based lubricant is perfect for sliding tight grips onto clean metal tubes. A quick 1- or 2-second blast into the open end of the grip is all it takes. Once installed, WD-40's chemical compound melts the grip interior just enough to make it stick to the bar like glue, without the mess. IMPORTANT: Wait 24 hours after installation before riding to give grips time to set up on the bars. Immediately after installation you can add safety wire wraps to both ends of the grips; this old motocross trick works great to reduce grip slip on the bars and throttle tube.

Every bike rider needs a rugged vest in their gear arsenal, and our 4-Speed Vest answers the call. Its heavy-duty cotton canvas exterior features generous sizing and elasticated expansion panels so you can layer it over a shirt, hoodie, or reinforced riding jacket. Two-way zipper with Hypalon pulls lets you fine-tune fit at the collar and waist. A breathable polyblend liner is built in to keep you warm and comfortable. Two interior and four exterior pockets are perfect for hauling gloves, glasses, and other EDC essentials.

Otto (6’2”, 185lb.) is wearing our Black 4-Speed vest in size Large over a Biltwell hoodie.

Features:

• Super-tough 13 oz. 100% cotton canvas exterior
• 3” wide canvas accordion side panels with stretch nylon/Elastane construction
• Heavy-duty Vislon two-way weatherproof zipper with high-traction Hypalon pulls
• Two lower front pockets with double-needle stitching and riveted corner reinforcements
• Oversized hidden pocket on right chest with 8-inch vertical zipper
• Single patch pocket on left chest
• Two interior patch pockets, one with internal elastic loop for key fob storage
• Breathable 57% polyester/43% Repreve recycled interior liner with sublimated graphic
• Woven stretch polyester collar with Spandex to hold shape
• Polyester single-needle, double-needle, and overlock stitched seams throughout
• High-quality embroidered interior tags and exterior brand detailing
• XS-XXL sizes

Care & Maintenance:

• Machine wash in cold water
• Do not machine dry
• Do not use bleach
• Do not dry clean
• Do not iron

Biltwell Kool Kan Gremmie

The ulitmate can and bottle holder for keeping your drink as chilled as you are.

Vinyl-coated Super Soft Foam construction gives unbelievable durability and insulating properties.

Made in the USA.