Street / Sport

Refer to diagram for dimensions.

Our Kung Fu grip's squishy surface design is cozy the second you grab it. New UV-resistant TPV synthetic rubber is soft, yet durable for miles of comfort.

Features:

• Comes as a pair
• Injection-molded Thermoplastic Vulcanizate synthetic rubber is soft, durable and highly UV-resistant
• Medium inside flange cushions rider's hands from rubbing the throttle and controls
• Thick outer flange for durability
• Safety wire grooves for added security
• Aftermarket throttle tube required to install Biltwell grips on stock H-D hand controls—see our Whiskey Throttle

Install Tips:

Counterintuitive though it might seem, aerosol WD-40 spray lubricant is our chemical of choice for installing Biltwell molded TPV grips. "But it's oil!" you say. Yes, but WD-40's combination of aerosol propellant and organic-based lubricant is perfect for sliding tight grips onto clean metal tubes. A quick 1 or 2-second blast into the open end of the grip is all it takes. Once installed, WD-40's chemical compound melts the grip interior just enough to make it stick to the bar like glue, without the mess. IMPORTANT: Wait 24 hours after installation before riding to give grips time to set up on the bars. Immediately after installation you can add safety wire wraps to both ends of the grips; this old motocross trick works great to reduce grip slip on the bars and throttle tube.

Refer to diagram for dimensions.

Our Kung Fu grip's squishy surface design is cozy the second you grab it. New UV-resistant TPV synthetic rubber is soft, yet durable for miles of comfort.

Features:

• Comes as a pair
• Injection-molded Thermoplastic Vulcanizate synthetic rubber is soft, durable and highly UV-resistant
• Medium inside flange cushions rider's hands from rubbing the throttle and controls
• Thick outer flange for durability
• Safety wire grooves for added security
• Aftermarket throttle tube required to install Biltwell grips on stock H-D hand controls—see our Whiskey Throttle

Install Tips:

Counterintuitive though it might seem, aerosol WD-40 spray lubricant is our chemical of choice for installing Biltwell molded TPV grips. "But it's oil!" you say. Yes, but WD-40's combination of aerosol propellant and organic-based lubricant is perfect for sliding tight grips onto clean metal tubes. A quick 1 or 2-second blast into the open end of the grip is all it takes. Once installed, WD-40's chemical compound melts the grip interior just enough to make it stick to the bar like glue, without the mess. IMPORTANT: Wait 24 hours after installation before riding to give grips time to set up on the bars. Immediately after installation you can add safety wire wraps to both ends of the grips; this old motocross trick works great to reduce grip slip on the bars and throttle tube.

Refer to diagram for dimensions.

Our Kung Fu grip's squishy surface design is cozy the second you grab it. New UV-resistant TPV synthetic rubber is soft, yet durable for miles of comfort.

Features:

• Comes as a pair
• Injection-molded Thermoplastic Vulcanizate synthetic rubber is soft, durable and highly UV-resistant
• Medium inside flange cushions rider's hands from rubbing the throttle and controls
• Thick outer flange for durability
• Safety wire grooves for added security
• Aftermarket throttle tube required to install Biltwell grips on stock H-D hand controls—see our Whiskey Throttle

Install Tips:

Counterintuitive though it might seem, aerosol WD-40 spray lubricant is our chemical of choice for installing Biltwell molded TPV grips. "But it's oil!" you say. Yes, but WD-40's combination of aerosol propellant and organic-based lubricant is perfect for sliding tight grips onto clean metal tubes. A quick 1 or 2-second blast into the open end of the grip is all it takes. Once installed, WD-40's chemical compound melts the grip interior just enough to make it stick to the bar like glue, without the mess. IMPORTANT: Wait 24 hours after installation before riding to give grips time to set up on the bars. Immediately after installation you can add safety wire wraps to both ends of the grips; this old motocross trick works great to reduce grip slip on the bars and throttle tube.

Refer to diagram for dimensions.

Our Kung Fu grip's squishy surface design is cozy the second you grab it. New UV-resistant TPV synthetic rubber is soft, yet durable for miles of comfort.

Features:

• Comes as a pair
• Injection-molded Thermoplastic Vulcanizate synthetic rubber is soft, durable and highly UV-resistant
• Medium inside flange cushions rider's hands from rubbing the throttle and controls
• Thick outer flange for durability
• Safety wire grooves for added security
• Aftermarket throttle tube required to install Biltwell grips on stock H-D hand controls—see our Whiskey Throttle

Install Tips:

Counterintuitive though it might seem, aerosol WD-40 spray lubricant is our chemical of choice for installing Biltwell molded TPV grips. "But it's oil!" you say. Yes, but WD-40's combination of aerosol propellant and organic-based lubricant is perfect for sliding tight grips onto clean metal tubes. A quick 1 or 2-second blast into the open end of the grip is all it takes. Once installed, WD-40's chemical compound melts the grip interior just enough to make it stick to the bar like glue, without the mess. IMPORTANT: Wait 24 hours after installation before riding to give grips time to set up on the bars. Immediately after installation you can add safety wire wraps to both ends of the grips; this old motocross trick works great to reduce grip slip on the bars and throttle tube.

Refer to diagram for dimensions.

Our Kung Fu grip's squishy surface design is cozy the second you grab it. New UV-resistant TPV synthetic rubber is soft, yet durable for miles of comfort.

Features:

• Comes as a pair
• Injection-molded Thermoplastic Vulcanizate synthetic rubber is soft, durable and highly UV-resistant
• Medium inside flange cushions rider's hands from rubbing the throttle and controls
• Thick outer flange for durability
• Safety wire grooves for added security
• Aftermarket throttle tube required to install Biltwell grips on stock H-D hand controls—see our Whiskey Throttle

Install Tips:

Counterintuitive though it might seem, aerosol WD-40 spray lubricant is our chemical of choice for installing Biltwell molded TPV grips. "But it's oil!" you say. Yes, but WD-40's combination of aerosol propellant and organic-based lubricant is perfect for sliding tight grips onto clean metal tubes. A quick 1 or 2-second blast into the open end of the grip is all it takes. Once installed, WD-40's chemical compound melts the grip interior just enough to make it stick to the bar like glue, without the mess. IMPORTANT: Wait 24 hours after installation before riding to give grips time to set up on the bars. Immediately after installation you can add safety wire wraps to both ends of the grips; this old motocross trick works great to reduce grip slip on the bars and throttle tube.

Refer to diagram for dimensions.

Our Kung Fu grip's squishy surface design is cozy the second you grab it. New UV-resistant TPV synthetic rubber is soft, yet durable for miles of comfort.

Features:

• Comes as a pair
• Injection-molded Thermoplastic Vulcanizate synthetic rubber is soft, durable and highly UV-resistant
• Medium inside flange cushions rider's hands from rubbing the throttle and controls
• Thick outer flange for durability
• Safety wire grooves for added security
• Aftermarket throttle tube required to install Biltwell grips on stock H-D hand controls—see our Whiskey Throttle

Install Tips:

Counterintuitive though it might seem, aerosol WD-40 spray lubricant is our chemical of choice for installing Biltwell molded TPV grips. "But it's oil!" you say. Yes, but WD-40's combination of aerosol propellant and organic-based lubricant is perfect for sliding tight grips onto clean metal tubes. A quick 1 or 2-second blast into the open end of the grip is all it takes. Once installed, WD-40's chemical compound melts the grip interior just enough to make it stick to the bar like glue, without the mess. IMPORTANT: Wait 24 hours after installation before riding to give grips time to set up on the bars. Immediately after installation you can add safety wire wraps to both ends of the grips; this old motocross trick works great to reduce grip slip on the bars and throttle tube.

Refer to diagram for dimensions.

Our Kung Fu grip's squishy surface design is cozy the second you grab it. New UV-resistant TPV synthetic rubber is soft, yet durable for miles of comfort.

Features:

• Comes as a pair
• Injection-molded Thermoplastic Vulcanizate synthetic rubber is soft, durable and highly UV-resistant
• Medium inside flange cushions rider's hands from rubbing the throttle and controls
• Thick outer flange for durability
• Safety wire grooves for added security
• Aftermarket throttle tube required to install Biltwell grips on stock H-D hand controls—see our Whiskey Throttle

Install Tips:

Counterintuitive though it might seem, aerosol WD-40 spray lubricant is our chemical of choice for installing Biltwell molded TPV grips. "But it's oil!" you say. Yes, but WD-40's combination of aerosol propellant and organic-based lubricant is perfect for sliding tight grips onto clean metal tubes. A quick 1 or 2-second blast into the open end of the grip is all it takes. Once installed, WD-40's chemical compound melts the grip interior just enough to make it stick to the bar like glue, without the mess. IMPORTANT: Wait 24 hours after installation before riding to give grips time to set up on the bars. Immediately after installation you can add safety wire wraps to both ends of the grips; this old motocross trick works great to reduce grip slip on the bars and throttle tube.

Refer to diagram for dimensions.

Our Kung Fu grip's squishy surface design is cozy the second you grab it. New UV-resistant TPV synthetic rubber is soft, yet durable for miles of comfort.

Features:

• Comes as a pair
• Injection-molded Thermoplastic Vulcanizate synthetic rubber is soft, durable and highly UV-resistant
• Medium inside flange cushions rider's hands from rubbing the throttle and controls
• Thick outer flange for durability
• Safety wire grooves for added security
• Aftermarket throttle tube required to install Biltwell grips on stock H-D hand controls—see our Whiskey Throttle

Install Tips:

Counterintuitive though it might seem, aerosol WD-40 spray lubricant is our chemical of choice for installing Biltwell molded TPV grips. "But it's oil!" you say. Yes, but WD-40's combination of aerosol propellant and organic-based lubricant is perfect for sliding tight grips onto clean metal tubes. A quick 1 or 2-second blast into the open end of the grip is all it takes. Once installed, WD-40's chemical compound melts the grip interior just enough to make it stick to the bar like glue, without the mess. IMPORTANT: Wait 24 hours after installation before riding to give grips time to set up on the bars. Immediately after installation you can add safety wire wraps to both ends of the grips; this old motocross trick works great to reduce grip slip on the bars and throttle tube.

Refer to diagram for dimensions.

Football-shaped cross section is fat in the middle and smaller on both ends to follow the contours of your open fist. Super durable and great looking, Recoil is our classic chopper grip

Features:

• Comes as a pair
• Injection-molded Thermoplastic Vulcanizate synthetic rubber is soft, durable and highly UV-resistant
• Thick, tapered one-piece molded end design for durability
• No inside flange give Recoil a classic chopper vibe
• Safety wire grooves on grip ends for added security
• Aftermarket throttle tube required to install Biltwell grips on stock H-D hand controls—see our Whiskey Throttle

Install Tips:

Counterintuitive though it might seem, aerosol WD-40 spray lubricant is our chemical of choice for installing Biltwell molded TPV grips. "But it's oil!" you say. Yes, but WD-40's combination of aerosol propellant and organic-based lubricant is perfect for sliding tight grips onto clean metal tubes. A quick 1 or 2-second blast into the open end of the grip is all it takes. Once installed, WD-40's chemical compound melts the grip interior just enough to make it stick to the bar like glue, without the mess. IMPORTANT: Wait 24 hours after installation before riding to give grips time to set up on the bars. Immediately after installation you can add safety wire wraps to both ends of the grips; this old motocross trick works great to reduce grip slip on the bars and throttle tube.

Refer to diagram for dimensions.

Football-shaped cross section is fat in the middle and smaller on both ends to follow the contours of your open fist. Super durable and great looking, Recoil is our classic chopper grip

Features:

• Comes as a pair
• Injection-molded Thermoplastic Vulcanizate synthetic rubber is soft, durable and highly UV-resistant
• Thick, tapered one-piece molded end design for durability
• No inside flange give Recoil a classic chopper vibe
• Safety wire grooves on grip ends for added security
• Aftermarket throttle tube required to install Biltwell grips on stock H-D hand controls—see our Whiskey Throttle

Install Tips:

Counterintuitive though it might seem, aerosol WD-40 spray lubricant is our chemical of choice for installing Biltwell molded TPV grips. "But it's oil!" you say. Yes, but WD-40's combination of aerosol propellant and organic-based lubricant is perfect for sliding tight grips onto clean metal tubes. A quick 1 or 2-second blast into the open end of the grip is all it takes. Once installed, WD-40's chemical compound melts the grip interior just enough to make it stick to the bar like glue, without the mess. IMPORTANT: Wait 24 hours after installation before riding to give grips time to set up on the bars. Immediately after installation you can add safety wire wraps to both ends of the grips; this old motocross trick works great to reduce grip slip on the bars and throttle tube.

Refer to diagram for dimensions.

Football-shaped cross section is fat in the middle and smaller on both ends to follow the contours of your open fist. Super durable and great looking, Recoil is our classic chopper grip

Features:

• Comes as a pair
• Injection-molded Thermoplastic Vulcanizate synthetic rubber is soft, durable and highly UV-resistant
• Thick, tapered one-piece molded end design for durability
• No inside flange give Recoil a classic chopper vibe
• Safety wire grooves on grip ends for added security
• Aftermarket throttle tube required to install Biltwell grips on stock H-D hand controls—see our Whiskey Throttle

Install Tips:

Counterintuitive though it might seem, aerosol WD-40 spray lubricant is our chemical of choice for installing Biltwell molded TPV grips. "But it's oil!" you say. Yes, but WD-40's combination of aerosol propellant and organic-based lubricant is perfect for sliding tight grips onto clean metal tubes. A quick 1 or 2-second blast into the open end of the grip is all it takes. Once installed, WD-40's chemical compound melts the grip interior just enough to make it stick to the bar like glue, without the mess. IMPORTANT: Wait 24 hours after installation before riding to give grips time to set up on the bars. Immediately after installation you can add safety wire wraps to both ends of the grips; this old motocross trick works great to reduce grip slip on the bars and throttle tube.

Refer to diagram for dimensions.

Football-shaped cross section is fat in the middle and smaller on both ends to follow the contours of your open fist. Super durable and great looking, Recoil is our classic chopper grip

Features:

• Comes as a pair
• Injection-molded Thermoplastic Vulcanizate synthetic rubber is soft, durable and highly UV-resistant
• Thick, tapered one-piece molded end design for durability
• No inside flange give Recoil a classic chopper vibe
• Safety wire grooves on grip ends for added security
• Aftermarket throttle tube required to install Biltwell grips on stock H-D hand controls—see our Whiskey Throttle

Install Tips:

Counterintuitive though it might seem, aerosol WD-40 spray lubricant is our chemical of choice for installing Biltwell molded TPV grips. "But it's oil!" you say. Yes, but WD-40's combination of aerosol propellant and organic-based lubricant is perfect for sliding tight grips onto clean metal tubes. A quick 1 or 2-second blast into the open end of the grip is all it takes. Once installed, WD-40's chemical compound melts the grip interior just enough to make it stick to the bar like glue, without the mess. IMPORTANT: Wait 24 hours after installation before riding to give grips time to set up on the bars. Immediately after installation you can add safety wire wraps to both ends of the grips; this old motocross trick works great to reduce grip slip on the bars and throttle tube.

Refer to diagram for dimensions.

Football-shaped cross section is fat in the middle and smaller on both ends to follow the contours of your open fist. Super durable and great looking, Recoil is our classic chopper grip

Features:

• Comes as a pair
• Injection-molded Thermoplastic Vulcanizate synthetic rubber is soft, durable and highly UV-resistant
• Thick, tapered one-piece molded end design for durability
• No inside flange give Recoil a classic chopper vibe
• Safety wire grooves on grip ends for added security
• Aftermarket throttle tube required to install Biltwell grips on stock H-D hand controls—see our Whiskey Throttle

Install Tips:

Counterintuitive though it might seem, aerosol WD-40 spray lubricant is our chemical of choice for installing Biltwell molded TPV grips. "But it's oil!" you say. Yes, but WD-40's combination of aerosol propellant and organic-based lubricant is perfect for sliding tight grips onto clean metal tubes. A quick 1 or 2-second blast into the open end of the grip is all it takes. Once installed, WD-40's chemical compound melts the grip interior just enough to make it stick to the bar like glue, without the mess. IMPORTANT: Wait 24 hours after installation before riding to give grips time to set up on the bars. Immediately after installation you can add safety wire wraps to both ends of the grips; this old motocross trick works great to reduce grip slip on the bars and throttle tube.

Refer to diagram for dimensions.

Football-shaped cross section is fat in the middle and smaller on both ends to follow the contours of your open fist. Super durable and great looking, Recoil is our classic chopper grip

Features:

• Comes as a pair
• Injection-molded Thermoplastic Vulcanizate synthetic rubber is soft, durable and highly UV-resistant
• Thick, tapered one-piece molded end design for durability
• No inside flange give Recoil a classic chopper vibe
• Safety wire grooves on grip ends for added security
• Aftermarket throttle tube required to install Biltwell grips on stock H-D hand controls—see our Whiskey Throttle

Install Tips:

Counterintuitive though it might seem, aerosol WD-40 spray lubricant is our chemical of choice for installing Biltwell molded TPV grips. "But it's oil!" you say. Yes, but WD-40's combination of aerosol propellant and organic-based lubricant is perfect for sliding tight grips onto clean metal tubes. A quick 1 or 2-second blast into the open end of the grip is all it takes. Once installed, WD-40's chemical compound melts the grip interior just enough to make it stick to the bar like glue, without the mess. IMPORTANT: Wait 24 hours after installation before riding to give grips time to set up on the bars. Immediately after installation you can add safety wire wraps to both ends of the grips; this old motocross trick works great to reduce grip slip on the bars and throttle tube.

Refer to diagram for dimensions.

Football-shaped cross section is fat in the middle and smaller on both ends to follow the contours of your open fist. Super durable and great looking, Recoil is our classic chopper grip

Features:

• Comes as a pair
• Injection-molded Thermoplastic Vulcanizate synthetic rubber is soft, durable and highly UV-resistant
• Thick, tapered one-piece molded end design for durability
• No inside flange give Recoil a classic chopper vibe
• Safety wire grooves on grip ends for added security
• Aftermarket throttle tube required to install Biltwell grips on stock H-D hand controls—see our Whiskey Throttle

Install Tips:

Counterintuitive though it might seem, aerosol WD-40 spray lubricant is our chemical of choice for installing Biltwell molded TPV grips. "But it's oil!" you say. Yes, but WD-40's combination of aerosol propellant and organic-based lubricant is perfect for sliding tight grips onto clean metal tubes. A quick 1 or 2-second blast into the open end of the grip is all it takes. Once installed, WD-40's chemical compound melts the grip interior just enough to make it stick to the bar like glue, without the mess. IMPORTANT: Wait 24 hours after installation before riding to give grips time to set up on the bars. Immediately after installation you can add safety wire wraps to both ends of the grips; this old motocross trick works great to reduce grip slip on the bars and throttle tube.

Refer to diagram for dimensions.

Football-shaped cross section is fat in the middle and smaller on both ends to follow the contours of your open fist. Super durable and great looking, Recoil is our classic chopper grip

Features:

• Comes as a pair
• Injection-molded Thermoplastic Vulcanizate synthetic rubber is soft, durable and highly UV-resistant
• Thick, tapered one-piece molded end design for durability
• No inside flange give Recoil a classic chopper vibe
• Safety wire grooves on grip ends for added security
• Aftermarket throttle tube required to install Biltwell grips on stock H-D hand controls—see our Whiskey Throttle

Install Tips:

Counterintuitive though it might seem, aerosol WD-40 spray lubricant is our chemical of choice for installing Biltwell molded TPV grips. "But it's oil!" you say. Yes, but WD-40's combination of aerosol propellant and organic-based lubricant is perfect for sliding tight grips onto clean metal tubes. A quick 1 or 2-second blast into the open end of the grip is all it takes. Once installed, WD-40's chemical compound melts the grip interior just enough to make it stick to the bar like glue, without the mess. IMPORTANT: Wait 24 hours after installation before riding to give grips time to set up on the bars. Immediately after installation you can add safety wire wraps to both ends of the grips; this old motocross trick works great to reduce grip slip on the bars and throttle tube.

Refer to diagram for dimensions.

Football-shaped cross section is fat in the middle and smaller on both ends to follow the contours of your open fist. Super durable and great looking, Recoil is our classic chopper grip

Features:

• Comes as a pair
• Injection-molded Thermoplastic Vulcanizate synthetic rubber is soft, durable and highly UV-resistant
• Thick, tapered one-piece molded end design for durability
• No inside flange give Recoil a classic chopper vibe
• Safety wire grooves on grip ends for added security
• Aftermarket throttle tube required to install Biltwell grips on stock H-D hand controls—see our Whiskey Throttle

Install Tips:

Counterintuitive though it might seem, aerosol WD-40 spray lubricant is our chemical of choice for installing Biltwell molded TPV grips. "But it's oil!" you say. Yes, but WD-40's combination of aerosol propellant and organic-based lubricant is perfect for sliding tight grips onto clean metal tubes. A quick 1 or 2-second blast into the open end of the grip is all it takes. Once installed, WD-40's chemical compound melts the grip interior just enough to make it stick to the bar like glue, without the mess. IMPORTANT: Wait 24 hours after installation before riding to give grips time to set up on the bars. Immediately after installation you can add safety wire wraps to both ends of the grips; this old motocross trick works great to reduce grip slip on the bars and throttle tube.

Refer to diagram for dimensions.

Renegade is identical to our Thruster model—tall flange, thick end cap—but features the football-shaped file pattern grip section as our Recoil grip. A great grip for big hands.

Features:

• Comes as a pair
• Injection-molded Thermoplastic Vulcanizate synthetic rubber is soft, durable and highly UV-resistant
• Thick one-piece molded end design for durability
• Tall inner flange protects your hands from discomfort against throttle and hand controls
• Safety wire grooves on grip ends for added security
• Aftermarket throttle tube required to install Biltwell grips on stock H-D hand controls—see our Whiskey Throttle

Install Tips:

Counterintuitive though it might seem, aerosol WD-40 spray lubricant is our chemical of choice for installing Biltwell molded TPV grips. "But it's oil!" you say. Yes, but WD-40's combination of aerosol propellant and organic-based lubricant is perfect for sliding tight grips onto clean metal tubes. A quick 1 or 2-second blast into the open end of the grip is all it takes. Once installed, WD-40's chemical compound melts the grip interior just enough to make it stick to the bar like glue, without the mess. IMPORTANT: Wait 24 hours after installation before riding to give grips time to set up on the bars. Immediately after installation you can add safety wire wraps to both ends of the grips; this old motocross trick works great to reduce grip slip on the bars and throttle tube.

Refer to diagram for dimensions.

Renegade is identical to our Thruster model—tall flange, thick end cap—but features the football-shaped file pattern grip section as our Recoil grip. A great grip for big hands.

Features:

• Comes as a pair
• Injection-molded Thermoplastic Vulcanizate synthetic rubber is soft, durable and highly UV-resistant
• Thick one-piece molded end design for durability
• Tall inner flange protects your hands from discomfort against throttle and hand controls
• Safety wire grooves on grip ends for added security
• Aftermarket throttle tube required to install Biltwell grips on stock H-D hand controls—see our Whiskey Throttle

Install Tips:

Counterintuitive though it might seem, aerosol WD-40 spray lubricant is our chemical of choice for installing Biltwell molded TPV grips. "But it's oil!" you say. Yes, but WD-40's combination of aerosol propellant and organic-based lubricant is perfect for sliding tight grips onto clean metal tubes. A quick 1 or 2-second blast into the open end of the grip is all it takes. Once installed, WD-40's chemical compound melts the grip interior just enough to make it stick to the bar like glue, without the mess. IMPORTANT: Wait 24 hours after installation before riding to give grips time to set up on the bars. Immediately after installation you can add safety wire wraps to both ends of the grips; this old motocross trick works great to reduce grip slip on the bars and throttle tube.

Refer to diagram for dimensions.

Renegade is identical to our Thruster model—tall flange, thick end cap—but features the football-shaped file pattern grip section as our Recoil grip. A great grip for big hands.

Features:

• Comes as a pair
• Injection-molded Thermoplastic Vulcanizate synthetic rubber is soft, durable and highly UV-resistant
• Thick one-piece molded end design for durability
• Tall inner flange protects your hands from discomfort against throttle and hand controls
• Safety wire grooves on grip ends for added security
• Aftermarket throttle tube required to install Biltwell grips on stock H-D hand controls—see our Whiskey Throttle

Install Tips:

Counterintuitive though it might seem, aerosol WD-40 spray lubricant is our chemical of choice for installing Biltwell molded TPV grips. "But it's oil!" you say. Yes, but WD-40's combination of aerosol propellant and organic-based lubricant is perfect for sliding tight grips onto clean metal tubes. A quick 1 or 2-second blast into the open end of the grip is all it takes. Once installed, WD-40's chemical compound melts the grip interior just enough to make it stick to the bar like glue, without the mess. IMPORTANT: Wait 24 hours after installation before riding to give grips time to set up on the bars. Immediately after installation you can add safety wire wraps to both ends of the grips; this old motocross trick works great to reduce grip slip on the bars and throttle tube.

Refer to diagram for dimensions.

Renegade is identical to our Thruster model—tall flange, thick end cap—but features the football-shaped file pattern grip section as our Recoil grip. A great grip for big hands.

Features:

• Comes as a pair
• Injection-molded Thermoplastic Vulcanizate synthetic rubber is soft, durable and highly UV-resistant
• Thick one-piece molded end design for durability
• Tall inner flange protects your hands from discomfort against throttle and hand controls
• Safety wire grooves on grip ends for added security
• Aftermarket throttle tube required to install Biltwell grips on stock H-D hand controls—see our Whiskey Throttle

Install Tips:

Counterintuitive though it might seem, aerosol WD-40 spray lubricant is our chemical of choice for installing Biltwell molded TPV grips. "But it's oil!" you say. Yes, but WD-40's combination of aerosol propellant and organic-based lubricant is perfect for sliding tight grips onto clean metal tubes. A quick 1 or 2-second blast into the open end of the grip is all it takes. Once installed, WD-40's chemical compound melts the grip interior just enough to make it stick to the bar like glue, without the mess. IMPORTANT: Wait 24 hours after installation before riding to give grips time to set up on the bars. Immediately after installation you can add safety wire wraps to both ends of the grips; this old motocross trick works great to reduce grip slip on the bars and throttle tube.

Refer to diagram for dimensions.

Renegade is identical to our Thruster model—tall flange, thick end cap—but features the football-shaped file pattern grip section as our Recoil grip. A great grip for big hands.

Features:

• Comes as a pair
• Injection-molded Thermoplastic Vulcanizate synthetic rubber is soft, durable and highly UV-resistant
• Thick one-piece molded end design for durability
• Tall inner flange protects your hands from discomfort against throttle and hand controls
• Safety wire grooves on grip ends for added security
• Aftermarket throttle tube required to install Biltwell grips on stock H-D hand controls—see our Whiskey Throttle

Install Tips:

Counterintuitive though it might seem, aerosol WD-40 spray lubricant is our chemical of choice for installing Biltwell molded TPV grips. "But it's oil!" you say. Yes, but WD-40's combination of aerosol propellant and organic-based lubricant is perfect for sliding tight grips onto clean metal tubes. A quick 1 or 2-second blast into the open end of the grip is all it takes. Once installed, WD-40's chemical compound melts the grip interior just enough to make it stick to the bar like glue, without the mess. IMPORTANT: Wait 24 hours after installation before riding to give grips time to set up on the bars. Immediately after installation you can add safety wire wraps to both ends of the grips; this old motocross trick works great to reduce grip slip on the bars and throttle tube.

Refer to diagram for dimensions.

Renegade is identical to our Thruster model—tall flange, thick end cap—but features the football-shaped file pattern grip section as our Recoil grip. A great grip for big hands.

Features:

• Comes as a pair
• Injection-molded Thermoplastic Vulcanizate synthetic rubber is soft, durable and highly UV-resistant
• Thick one-piece molded end design for durability
• Tall inner flange protects your hands from discomfort against throttle and hand controls
• Safety wire grooves on grip ends for added security
• Aftermarket throttle tube required to install Biltwell grips on stock H-D hand controls—see our Whiskey Throttle

Install Tips:

Counterintuitive though it might seem, aerosol WD-40 spray lubricant is our chemical of choice for installing Biltwell molded TPV grips. "But it's oil!" you say. Yes, but WD-40's combination of aerosol propellant and organic-based lubricant is perfect for sliding tight grips onto clean metal tubes. A quick 1 or 2-second blast into the open end of the grip is all it takes. Once installed, WD-40's chemical compound melts the grip interior just enough to make it stick to the bar like glue, without the mess. IMPORTANT: Wait 24 hours after installation before riding to give grips time to set up on the bars. Immediately after installation you can add safety wire wraps to both ends of the grips; this old motocross trick works great to reduce grip slip on the bars and throttle tube.

Refer to diagram for dimensions.

Renegade is identical to our Thruster model—tall flange, thick end cap—but features the football-shaped file pattern grip section as our Recoil grip. A great grip for big hands.

Features:

• Comes as a pair
• Injection-molded Thermoplastic Vulcanizate synthetic rubber is soft, durable and highly UV-resistant
• Thick one-piece molded end design for durability
• Tall inner flange protects your hands from discomfort against throttle and hand controls
• Safety wire grooves on grip ends for added security
• Aftermarket throttle tube required to install Biltwell grips on stock H-D hand controls—see our Whiskey Throttle

Install Tips:

Counterintuitive though it might seem, aerosol WD-40 spray lubricant is our chemical of choice for installing Biltwell molded TPV grips. "But it's oil!" you say. Yes, but WD-40's combination of aerosol propellant and organic-based lubricant is perfect for sliding tight grips onto clean metal tubes. A quick 1 or 2-second blast into the open end of the grip is all it takes. Once installed, WD-40's chemical compound melts the grip interior just enough to make it stick to the bar like glue, without the mess. IMPORTANT: Wait 24 hours after installation before riding to give grips time to set up on the bars. Immediately after installation you can add safety wire wraps to both ends of the grips; this old motocross trick works great to reduce grip slip on the bars and throttle tube.

Refer to diagram for dimensions.

Renegade is identical to our Thruster model—tall flange, thick end cap—but features the football-shaped file pattern grip section as our Recoil grip. A great grip for big hands.

Features:

• Comes as a pair
• Injection-molded Thermoplastic Vulcanizate synthetic rubber is soft, durable and highly UV-resistant
• Thick one-piece molded end design for durability
• Tall inner flange protects your hands from discomfort against throttle and hand controls
• Safety wire grooves on grip ends for added security
• Aftermarket throttle tube required to install Biltwell grips on stock H-D hand controls—see our Whiskey Throttle

Install Tips:

Counterintuitive though it might seem, aerosol WD-40 spray lubricant is our chemical of choice for installing Biltwell molded TPV grips. "But it's oil!" you say. Yes, but WD-40's combination of aerosol propellant and organic-based lubricant is perfect for sliding tight grips onto clean metal tubes. A quick 1 or 2-second blast into the open end of the grip is all it takes. Once installed, WD-40's chemical compound melts the grip interior just enough to make it stick to the bar like glue, without the mess. IMPORTANT: Wait 24 hours after installation before riding to give grips time to set up on the bars. Immediately after installation you can add safety wire wraps to both ends of the grips; this old motocross trick works great to reduce grip slip on the bars and throttle tube.

Refer to diagram for dimensions.

Thruster uses the same padded diamond surface as our Torker grip, but features a tall inside flange and thick molded end cap for a retro MX look and feel.

Features:

• Comes as a pair
• Injection-molded Thermoplastic Vulcanizate synthetic rubber is soft, durable and highly UV-resistant
• Thick one-piece molded end design for durability
• Tall inner flange protects your hands from discomfort against throttle and hand controls
• Safety wire grooves for added security
• Aftermarket throttle tube required to install Biltwell grips on stock H-D hand controls—see our Whiskey Throttle

Install Tips:

Counterintuitive though it might seem, aerosol WD-40 spray lubricant is our chemical of choice for installing Biltwell molded TPV grips. "But it's oil!" you say. Yes, but WD-40's combination of aerosol propellant and organic-based lubricant is perfect for sliding tight grips onto clean metal tubes. A quick 1 or 2-second blast into the open end of the grip is all it takes. Once installed, WD-40's chemical compound melts the grip interior just enough to make it stick to the bar like glue, without the mess. IMPORTANT: Wait 24 hours after installation before riding to give grips time to set up on the bars. Immediately after installation you can add safety wire wraps to both ends of the grips; this old motocross trick works great to reduce grip slip on the bars and throttle tube.

Refer to diagram for dimensions.

Thruster uses the same padded diamond surface as our Torker grip, but features a tall inside flange and thick molded end cap for a retro MX look and feel.

Features:

• Comes as a pair
• Injection-molded Thermoplastic Vulcanizate synthetic rubber is soft, durable and highly UV-resistant
• Thick one-piece molded end design for durability
• Tall inner flange protects your hands from discomfort against throttle and hand controls
• Safety wire grooves for added security
• Aftermarket throttle tube required to install Biltwell grips on stock H-D hand controls—see our Whiskey Throttle

Install Tips:

Counterintuitive though it might seem, aerosol WD-40 spray lubricant is our chemical of choice for installing Biltwell molded TPV grips. "But it's oil!" you say. Yes, but WD-40's combination of aerosol propellant and organic-based lubricant is perfect for sliding tight grips onto clean metal tubes. A quick 1 or 2-second blast into the open end of the grip is all it takes. Once installed, WD-40's chemical compound melts the grip interior just enough to make it stick to the bar like glue, without the mess. IMPORTANT: Wait 24 hours after installation before riding to give grips time to set up on the bars. Immediately after installation you can add safety wire wraps to both ends of the grips; this old motocross trick works great to reduce grip slip on the bars and throttle tube.

Refer to diagram for dimensions.

Thruster uses the same padded diamond surface as our Torker grip, but features a tall inside flange and thick molded end cap for a retro MX look and feel.

Features:

• Comes as a pair
• Injection-molded Thermoplastic Vulcanizate synthetic rubber is soft, durable and highly UV-resistant
• Thick one-piece molded end design for durability
• Tall inner flange protects your hands from discomfort against throttle and hand controls
• Safety wire grooves for added security
• Aftermarket throttle tube required to install Biltwell grips on stock H-D hand controls—see our Whiskey Throttle

Install Tips:

Counterintuitive though it might seem, aerosol WD-40 spray lubricant is our chemical of choice for installing Biltwell molded TPV grips. "But it's oil!" you say. Yes, but WD-40's combination of aerosol propellant and organic-based lubricant is perfect for sliding tight grips onto clean metal tubes. A quick 1 or 2-second blast into the open end of the grip is all it takes. Once installed, WD-40's chemical compound melts the grip interior just enough to make it stick to the bar like glue, without the mess. IMPORTANT: Wait 24 hours after installation before riding to give grips time to set up on the bars. Immediately after installation you can add safety wire wraps to both ends of the grips; this old motocross trick works great to reduce grip slip on the bars and throttle tube.

Refer to diagram for dimensions.

Thruster uses the same padded diamond surface as our Torker grip, but features a tall inside flange and thick molded end cap for a retro MX look and feel.

Features:

• Comes as a pair
• Injection-molded Thermoplastic Vulcanizate synthetic rubber is soft, durable and highly UV-resistant
• Thick one-piece molded end design for durability
• Tall inner flange protects your hands from discomfort against throttle and hand controls
• Safety wire grooves for added security
• Aftermarket throttle tube required to install Biltwell grips on stock H-D hand controls—see our Whiskey Throttle

Install Tips:

Counterintuitive though it might seem, aerosol WD-40 spray lubricant is our chemical of choice for installing Biltwell molded TPV grips. "But it's oil!" you say. Yes, but WD-40's combination of aerosol propellant and organic-based lubricant is perfect for sliding tight grips onto clean metal tubes. A quick 1 or 2-second blast into the open end of the grip is all it takes. Once installed, WD-40's chemical compound melts the grip interior just enough to make it stick to the bar like glue, without the mess. IMPORTANT: Wait 24 hours after installation before riding to give grips time to set up on the bars. Immediately after installation you can add safety wire wraps to both ends of the grips; this old motocross trick works great to reduce grip slip on the bars and throttle tube.

Refer to diagram for dimensions.

Thruster uses the same padded diamond surface as our Torker grip, but features a tall inside flange and thick molded end cap for a retro MX look and feel.

Features:

• Comes as a pair
• Injection-molded Thermoplastic Vulcanizate synthetic rubber is soft, durable and highly UV-resistant
• Thick one-piece molded end design for durability
• Tall inner flange protects your hands from discomfort against throttle and hand controls
• Safety wire grooves for added security
• Aftermarket throttle tube required to install Biltwell grips on stock H-D hand controls—see our Whiskey Throttle

Install Tips:

Counterintuitive though it might seem, aerosol WD-40 spray lubricant is our chemical of choice for installing Biltwell molded TPV grips. "But it's oil!" you say. Yes, but WD-40's combination of aerosol propellant and organic-based lubricant is perfect for sliding tight grips onto clean metal tubes. A quick 1 or 2-second blast into the open end of the grip is all it takes. Once installed, WD-40's chemical compound melts the grip interior just enough to make it stick to the bar like glue, without the mess. IMPORTANT: Wait 24 hours after installation before riding to give grips time to set up on the bars. Immediately after installation you can add safety wire wraps to both ends of the grips; this old motocross trick works great to reduce grip slip on the bars and throttle tube.

Refer to diagram for dimensions.

Thruster uses the same padded diamond surface as our Torker grip, but features a tall inside flange and thick molded end cap for a retro MX look and feel.

Features:

• Comes as a pair
• Injection-molded Thermoplastic Vulcanizate synthetic rubber is soft, durable and highly UV-resistant
• Thick one-piece molded end design for durability
• Tall inner flange protects your hands from discomfort against throttle and hand controls
• Safety wire grooves for added security
• Aftermarket throttle tube required to install Biltwell grips on stock H-D hand controls—see our Whiskey Throttle

Install Tips:

Counterintuitive though it might seem, aerosol WD-40 spray lubricant is our chemical of choice for installing Biltwell molded TPV grips. "But it's oil!" you say. Yes, but WD-40's combination of aerosol propellant and organic-based lubricant is perfect for sliding tight grips onto clean metal tubes. A quick 1 or 2-second blast into the open end of the grip is all it takes. Once installed, WD-40's chemical compound melts the grip interior just enough to make it stick to the bar like glue, without the mess. IMPORTANT: Wait 24 hours after installation before riding to give grips time to set up on the bars. Immediately after installation you can add safety wire wraps to both ends of the grips; this old motocross trick works great to reduce grip slip on the bars and throttle tube.

Refer to diagram for dimensions.

Thruster uses the same padded diamond surface as our Torker grip, but features a tall inside flange and thick molded end cap for a retro MX look and feel.

Features:

• Comes as a pair
• Injection-molded Thermoplastic Vulcanizate synthetic rubber is soft, durable and highly UV-resistant
• Thick one-piece molded end design for durability
• Tall inner flange protects your hands from discomfort against throttle and hand controls
• Safety wire grooves for added security
• Aftermarket throttle tube required to install Biltwell grips on stock H-D hand controls—see our Whiskey Throttle

Install Tips:

Counterintuitive though it might seem, aerosol WD-40 spray lubricant is our chemical of choice for installing Biltwell molded TPV grips. "But it's oil!" you say. Yes, but WD-40's combination of aerosol propellant and organic-based lubricant is perfect for sliding tight grips onto clean metal tubes. A quick 1 or 2-second blast into the open end of the grip is all it takes. Once installed, WD-40's chemical compound melts the grip interior just enough to make it stick to the bar like glue, without the mess. IMPORTANT: Wait 24 hours after installation before riding to give grips time to set up on the bars. Immediately after installation you can add safety wire wraps to both ends of the grips; this old motocross trick works great to reduce grip slip on the bars and throttle tube.

Refer to diagram for dimensions.

Diamond pillow surfacing is comfortable, but wears like the sole on a boot. No inside flange makes our Torker grip a great choice for aftermarket throttles—clean and lean.

Features:

• Comes as a pair
• Injection-molded Thermoplastic Vulcanizate synthetic rubber is soft, durable and highly UV-resistant
• Flangeless design looks great on café racers, vintage Japanese and British customs and modern cruisers
• Thick one-piece molded end design for durability
• Safety wire grooves for added security
• Aftermarket throttle tube required to install Biltwell grips on stock H-D hand controls—see our Whiskey Throttle

Install Tips:

Counterintuitive though it might seem, aerosol WD-40 spray lubricant is our chemical of choice for installing Biltwell molded TPV grips. "But it's oil!" you say. Yes, but WD-40's combination of aerosol propellant and organic-based lubricant is perfect for sliding tight grips onto clean metal tubes. A quick 1 or 2-second blast into the open end of the grip is all it takes. Once installed, WD-40's chemical compound melts the grip interior just enough to make it stick to the bar like glue, without the mess. IMPORTANT: Wait 24 hours after installation before riding to give grips time to set up on the bars. Immediately after installation you can add safety wire wraps to both ends of the grips; this old motocross trick works great to reduce grip slip on the bars and throttle tube.

Refer to diagram for dimensions.

Diamond pillow surfacing is comfortable, but wears like the sole on a boot. No inside flange makes our Torker grip a great choice for aftermarket throttles—clean and lean.

Features:

• Comes as a pair
• Injection-molded Thermoplastic Vulcanizate synthetic rubber is soft, durable and highly UV-resistant
• Flangeless design looks great on café racers, vintage Japanese and British customs and modern cruisers
• Thick one-piece molded end design for durability
• Safety wire grooves for added security
• Aftermarket throttle tube required to install Biltwell grips on stock H-D hand controls—see our Whiskey Throttle

Install Tips:

Counterintuitive though it might seem, aerosol WD-40 spray lubricant is our chemical of choice for installing Biltwell molded TPV grips. "But it's oil!" you say. Yes, but WD-40's combination of aerosol propellant and organic-based lubricant is perfect for sliding tight grips onto clean metal tubes. A quick 1 or 2-second blast into the open end of the grip is all it takes. Once installed, WD-40's chemical compound melts the grip interior just enough to make it stick to the bar like glue, without the mess. IMPORTANT: Wait 24 hours after installation before riding to give grips time to set up on the bars. Immediately after installation you can add safety wire wraps to both ends of the grips; this old motocross trick works great to reduce grip slip on the bars and throttle tube.

Refer to diagram for dimensions.

Diamond pillow surfacing is comfortable, but wears like the sole on a boot. No inside flange makes our Torker grip a great choice for aftermarket throttles—clean and lean.

Features:

• Comes as a pair
• Injection-molded Thermoplastic Vulcanizate synthetic rubber is soft, durable and highly UV-resistant
• Flangeless design looks great on café racers, vintage Japanese and British customs and modern cruisers
• Thick one-piece molded end design for durability
• Safety wire grooves for added security
• Aftermarket throttle tube required to install Biltwell grips on stock H-D hand controls—see our Whiskey Throttle

Install Tips:

Counterintuitive though it might seem, aerosol WD-40 spray lubricant is our chemical of choice for installing Biltwell molded TPV grips. "But it's oil!" you say. Yes, but WD-40's combination of aerosol propellant and organic-based lubricant is perfect for sliding tight grips onto clean metal tubes. A quick 1 or 2-second blast into the open end of the grip is all it takes. Once installed, WD-40's chemical compound melts the grip interior just enough to make it stick to the bar like glue, without the mess. IMPORTANT: Wait 24 hours after installation before riding to give grips time to set up on the bars. Immediately after installation you can add safety wire wraps to both ends of the grips; this old motocross trick works great to reduce grip slip on the bars and throttle tube.

Refer to diagram for dimensions.

Diamond pillow surfacing is comfortable, but wears like the sole on a boot. No inside flange makes our Torker grip a great choice for aftermarket throttles—clean and lean.

Features:

• Comes as a pair
• Injection-molded Thermoplastic Vulcanizate synthetic rubber is soft, durable and highly UV-resistant
• Flangeless design looks great on café racers, vintage Japanese and British customs and modern cruisers
• Thick one-piece molded end design for durability
• Safety wire grooves for added security
• Aftermarket throttle tube required to install Biltwell grips on stock H-D hand controls—see our Whiskey Throttle

Install Tips:

Counterintuitive though it might seem, aerosol WD-40 spray lubricant is our chemical of choice for installing Biltwell molded TPV grips. "But it's oil!" you say. Yes, but WD-40's combination of aerosol propellant and organic-based lubricant is perfect for sliding tight grips onto clean metal tubes. A quick 1 or 2-second blast into the open end of the grip is all it takes. Once installed, WD-40's chemical compound melts the grip interior just enough to make it stick to the bar like glue, without the mess. IMPORTANT: Wait 24 hours after installation before riding to give grips time to set up on the bars. Immediately after installation you can add safety wire wraps to both ends of the grips; this old motocross trick works great to reduce grip slip on the bars and throttle tube.

Refer to diagram for dimensions.

Diamond pillow surfacing is comfortable, but wears like the sole on a boot. No inside flange makes our Torker grip a great choice for aftermarket throttles—clean and lean.

Features:

• Comes as a pair
• Injection-molded Thermoplastic Vulcanizate synthetic rubber is soft, durable and highly UV-resistant
• Flangeless design looks great on café racers, vintage Japanese and British customs and modern cruisers
• Thick one-piece molded end design for durability
• Safety wire grooves for added security
• Aftermarket throttle tube required to install Biltwell grips on stock H-D hand controls—see our Whiskey Throttle

Install Tips:

Counterintuitive though it might seem, aerosol WD-40 spray lubricant is our chemical of choice for installing Biltwell molded TPV grips. "But it's oil!" you say. Yes, but WD-40's combination of aerosol propellant and organic-based lubricant is perfect for sliding tight grips onto clean metal tubes. A quick 1 or 2-second blast into the open end of the grip is all it takes. Once installed, WD-40's chemical compound melts the grip interior just enough to make it stick to the bar like glue, without the mess. IMPORTANT: Wait 24 hours after installation before riding to give grips time to set up on the bars. Immediately after installation you can add safety wire wraps to both ends of the grips; this old motocross trick works great to reduce grip slip on the bars and throttle tube.

Refer to diagram for dimensions.

Diamond pillow surfacing is comfortable, but wears like the sole on a boot. No inside flange makes our Torker grip a great choice for aftermarket throttles—clean and lean.

Features:

• Comes as a pair
• Injection-molded Thermoplastic Vulcanizate synthetic rubber is soft, durable and highly UV-resistant
• Flangeless design looks great on café racers, vintage Japanese and British customs and modern cruisers
• Thick one-piece molded end design for durability
• Safety wire grooves for added security
• Aftermarket throttle tube required to install Biltwell grips on stock H-D hand controls—see our Whiskey Throttle

Install Tips:

Counterintuitive though it might seem, aerosol WD-40 spray lubricant is our chemical of choice for installing Biltwell molded TPV grips. "But it's oil!" you say. Yes, but WD-40's combination of aerosol propellant and organic-based lubricant is perfect for sliding tight grips onto clean metal tubes. A quick 1 or 2-second blast into the open end of the grip is all it takes. Once installed, WD-40's chemical compound melts the grip interior just enough to make it stick to the bar like glue, without the mess. IMPORTANT: Wait 24 hours after installation before riding to give grips time to set up on the bars. Immediately after installation you can add safety wire wraps to both ends of the grips; this old motocross trick works great to reduce grip slip on the bars and throttle tube.

Refer to diagram for dimensions.

Diamond pillow surfacing is comfortable, but wears like the sole on a boot. No inside flange makes our Torker grip a great choice for aftermarket throttles—clean and lean.

Features:

• Comes as a pair
• Injection-molded Thermoplastic Vulcanizate synthetic rubber is soft, durable and highly UV-resistant
• Flangeless design looks great on café racers, vintage Japanese and British customs and modern cruisers
• Thick one-piece molded end design for durability
• Safety wire grooves for added security
• Aftermarket throttle tube required to install Biltwell grips on stock H-D hand controls—see our Whiskey Throttle

Install Tips:

Counterintuitive though it might seem, aerosol WD-40 spray lubricant is our chemical of choice for installing Biltwell molded TPV grips. "But it's oil!" you say. Yes, but WD-40's combination of aerosol propellant and organic-based lubricant is perfect for sliding tight grips onto clean metal tubes. A quick 1 or 2-second blast into the open end of the grip is all it takes. Once installed, WD-40's chemical compound melts the grip interior just enough to make it stick to the bar like glue, without the mess. IMPORTANT: Wait 24 hours after installation before riding to give grips time to set up on the bars. Immediately after installation you can add safety wire wraps to both ends of the grips; this old motocross trick works great to reduce grip slip on the bars and throttle tube.

Refer to diagram for dimensions.

Diamond pillow surfacing is comfortable, but wears like the sole on a boot. No inside flange makes our Torker grip a great choice for aftermarket throttles—clean and lean.

Features:

• Comes as a pair
• Injection-molded Thermoplastic Vulcanizate synthetic rubber is soft, durable and highly UV-resistant
• Flangeless design looks great on café racers, vintage Japanese and British customs and modern cruisers
• Thick one-piece molded end design for durability
• Safety wire grooves for added security
• Aftermarket throttle tube required to install Biltwell grips on stock H-D hand controls—see our Whiskey Throttle

Install Tips:

Counterintuitive though it might seem, aerosol WD-40 spray lubricant is our chemical of choice for installing Biltwell molded TPV grips. "But it's oil!" you say. Yes, but WD-40's combination of aerosol propellant and organic-based lubricant is perfect for sliding tight grips onto clean metal tubes. A quick 1 or 2-second blast into the open end of the grip is all it takes. Once installed, WD-40's chemical compound melts the grip interior just enough to make it stick to the bar like glue, without the mess. IMPORTANT: Wait 24 hours after installation before riding to give grips time to set up on the bars. Immediately after installation you can add safety wire wraps to both ends of the grips; this old motocross trick works great to reduce grip slip on the bars and throttle tube.