Road Parts

EBC SFA Organic Scooter Brake Pads

EBC Brakes Organic replacement scooter brake pads, the SFA series organic range are a great choice for everyday commuter use on modern scooters and lighter motorcycles. SFA pads provide the instantly available stopping power desired for urban scooter brakes.

Features:

• Premium organic compound

• Can be used to replace organic or sintered

• Replaces all pad types

• Low metallic means absolutely NO disc damage

• Superb finger tip brake power and control

• Medium plus lifetime, ideal for general urban riding

• ECO friendly with zero toxic ingredients

Find the correct fitment for your scooter or motorcycle here: EBC Brakes Fitment Guide

Simple and efficient, Toplite’s line of 6 volt conventional batteries carry the unparalleled quality of any battery bearing the Toplite by Yuasa name.

Features:

• Special thin separators which provide high cranking power

• Engineered to protect against corrosion, withstand vibration, and deliver high cranking power

Find the correct fitment for your motorcycle here: Toplite-Yuasa Fitment Guide

Clip (Conn) type link for Tsubaki Gamma 420 Chain.

Refer to diagram for dimensions.

Thruster uses the same padded diamond surface as our Torker grip, but features a tall inside flange and thick molded end cap for a retro MX look and feel.

Features:

• Comes as a pair
• Injection-molded Thermoplastic Vulcanizate synthetic rubber is soft, durable and highly UV-resistant
• Thick one-piece molded end design for durability
• Tall inner flange protects your hands from discomfort against throttle and hand controls
• Safety wire grooves for added security
• Aftermarket throttle tube required to install Biltwell grips on stock H-D hand controls—see our Whiskey Throttle

Install Tips:

Counterintuitive though it might seem, aerosol WD-40 spray lubricant is our chemical of choice for installing Biltwell molded TPV grips. "But it's oil!" you say. Yes, but WD-40's combination of aerosol propellant and organic-based lubricant is perfect for sliding tight grips onto clean metal tubes. A quick 1 or 2-second blast into the open end of the grip is all it takes. Once installed, WD-40's chemical compound melts the grip interior just enough to make it stick to the bar like glue, without the mess. IMPORTANT: Wait 24 hours after installation before riding to give grips time to set up on the bars. Immediately after installation you can add safety wire wraps to both ends of the grips; this old motocross trick works great to reduce grip slip on the bars and throttle tube.

BB10L-A2/B2 battery is a part of our SLA range. Designed to make the user life easier, this 12V 11.6Ah battery is ready to use, 100% maintenance free and completely spill proof.

Extremely simple to install & carry, this BB10L-A2/B2 battery offers increased power, extended life and maximum reliability to all powersport vehicles that require high performance.

Specifications:

• Technology: SLA
• Voltage (V): 12
• Capacity 10hr (Ah): 11
• Capacity 20hr (Ah): 11.6
• CCA (A): 120
• Polartiy:
• Terminal:
• Dimensions (mm): 133 x 90 x 145

Features:

• Wet charged factory activated and ready to go
• Higher life cycle (up to three times longer than conventional batteries)
• Easy to install (no risk of spilling acid)
• Plate sulfation minimized
• AGM construction (absorbed acid)
• VRLA battery (Valve Regulated Lead Acid)
• Sealed, no gas emission through venting hole (under normal operation)
• Increased power and extended life
• Extreme vibration resistance

Find the correct fitment for your motorcycle here: BS Battery Fitment Guide

BTZ12S battery is a part of our SLA range. Designed to make the user life easier, this 12V 11.6Ah battery is ready to use, 100% maintenance free and completely spill proof.

Extremely simple to install & carry, this BTX12 battery offers increased power, extended life and maximum reliability to all powersport vehicles that require high performance.

Specifications:

• Technology: SLA
• Voltage (V): 12
• Capacity 10hr (Ah): 11
• Capacity 20hr (Ah): 11.6
• CCA (A): 215
• Polartiy:
• Terminal:
• Dimensions (mm): 150 x 88 x 110

Features:

• Wet charged factory activated and ready to go
• Higher life cycle (up to three times longer than conventional batteries)
• Easy to install (no risk of spilling acid)
• Plate sulfation minimized
• AGM construction (absorbed acid)
• VRLA battery (Valve Regulated Lead Acid)
• Sealed, no gas emission through venting hole (under normal operation)
• Increased power and extended life
• Extreme vibration resistance

Find the correct fitment for your motorcycle here: BS Battery Fitment Guide

Mainly developed for warehouses and garages, the brand-new BK 20 is a smart bank battery charger and maintainer, which offers 3 channels of charge.

Rated at 2A per channel, this powerful automatic charger is suitable for lead acid and lithium batteries up to 40Ah. Real 3 in 1 solution, the BK 20 can charge and maintain 3 batteries with different voltage and technologies at once.

Very safe and easy to use, the BK 20 has 10 stages of charge including a new force mode to enhance the performance of all your powersports batteries. Delivered with 3 BS clamps set.

Assembly part for display can be addded in option to mount up to two BK 20 chargers on BS display. Ideal to create a small charging station!

Features:
  Charges and maintains 3 batteries with different voltage and technologies at once
  Adaptable charging algorithm for Lead Acid & Lithium (LiFePO4)
  Easy to use: connect & forget
  Auto detect Lead Acid or Lithium technology
  Force mode: to activate low voltage “dead” Lead Acid battery or wake up “dead” LiFePO4 battery
  Safe: connection spark free, reverse polarity, short circuit and internal overheat protection 

Get back on the road in no time thanks to our ultra compact and powerful battery jump starter!

The Power Box is versatile to safely jump start battery on all vehicles, charge and recharge USB devices including 3 light modes in case of emergency. Ultra safe, our booster PB 02 is delivered with a smart cable to ensure spark-proof connec-tion and reverse polarity protection. Thanks to a com-pact and lightweight conception, you can easily you
can easily insert your PB 02 inside a motorcycle, trunk, glove box, or adventurer backpack.

Features:
  Compact and powerful booster rated at 1200A
  Suitable for 12V Lead Acid battery only.
  Up to 20 jump starts in one charge.
  Designed for gas (7.0L) and diesel (6.0L) engines.
  Very safe: smart cable with spark-proof connection and reverse polarity protection.
  Power supply for all USB devices when you need them most.
  LED flashlight function with 3 modes.
  LCD display with state of charge indication and output ports used.
  Comes with a storage case, smart jump lead, lightning cable, Micro USB cable, USB C cable, 12V car charger and 12V home charger.

Functions:
  Safe lithium Booster
  Gas engines up to 7.0L
  Diesel engines up to 6L
 
  LED Flashlight
  3 modes – Powerful constant light
  Strobe & SOS

  Power Supply
  USB output 5V 2A for mobile devices
  Output 12V for vehicle products
  Battery charger for mobile devices

Battery Booster For:
  Motorcycle, Scooter, ATV, SSV-UTB, Snowmobile, Watercraft, Lawn & Garden, Car, Boat

Battery Charger For:
  Mobile Devices: Smartphones, tablets, HD action cameras, music players, wireless speakers and more !

Organic FA Brake Pads by EBC for road motorcycles. UK made using high tech ECO friendly pad compound that delivers fingertip stopping power. Suitable for all road bikes and scooters, the E327 grade compound has been a best seller for many years with over 40 million sets sold worldwide. Fully TÜV tested and now ECE R 90 brake safety test appoved, these pads were rated by German Motorrad Magazine as a top quality organic pad and now proven suitable even as a sintered pad replacement. All EBC organic pads are built on backing plates made with the patented Nucap NRS hook retention system guaranteeing zero chance of pad debonding after extended use or corrosion.

Features:

• Superb streetbike pad
• Totally ECO friendly
• Can replace organic or sintered
• TÜV and ECE R 90 approved
• Low dust and rotor abrasion
• Expertly crafted from the highest grade materials
• Will deliver years of reliable service
• Made to withstand the harshest conditions

Find the correct fitment for your motorcycle here: EBC Brakes Fitment Guide

Double-H Sintered Brake Pads by EBC. Double-H Sintered Brake Pads deliver high performance and are well known as the EBC flagship sintered street-sport brake pad. ECE R 90 brake safety approved and TUV tested, these ultra high friction HH rated brake pads remain a market leader above the rest. Manufactured in the US in the state-of-the-art sintering plant in Ohio, Double-H Sintered Brake Pads perform well in all weather conditions be it dry or wet and have a high longevity lasting for many miles.

Features:

• Expertly crafted from the highest grade materials
• Will deliver years of reliable service
• Made to withstand the harshest conditions
• Gives perfect braking in both wet and dry conditions

Pro-Lite Front Discs
• Compete “Hub and Rotor” units for direct bolt-on.
• Assembled with sturdy RIVETS.
• Disc rings made from roll forged BILLET STEEL offering 18% more stopping power than stainless steel but with the high strength of steel... better braking and NO risk of cracking as with cast iron rotors.
• Lightweight forged alloy center hub using special high strength ductile mill rolled aluminium alloy, coloured either silver or gold to match bike cosmetics.
• Pro-lite discs resist distortion longer PLUS the unique “Birdswing” drill pattern prevents ridges developing on the rotor.

Rear Discs
• Unique birdswing drill pattern prevents ridges.
• Tough HPSR steel prevents cracking.
• Silver Zinc finish to prevent corrosion.

Standard replacement discs for modern streetbikes made with the EBC unique birdswing drill pattern. Holes overlap such that as pad and disc wears, no ridges are generated, pads stay flatter and last longer.

Find the correct fitment for your scooter or motorcycle here: EBC Brakes Fitment Guide

Indent Orders available for items not in stock or not listed.
(Air freight indents are 2 - 6 weeks delivery subject to availability)

Front Circular profile

• Front or Rear fitments.
• New Lightweight construction.
• Radical new profile.
• Heat treated carbon steel.
• Gold zinc anodised.

Front Contoured profile

Now available for most popular Moto-X machines, EBC’s new Supercross Contour discs have proved not only to provide a trick looking brake setup, but also deliver great and improved brake feel over conventional solid discs, according to many moto-x riders.

• Extra weight reduction reducing unsprung weight.
• Super trick looking contoured profile.
• Made from heat treated carbon steel with higher friction than stainless steel equals more stopping power.
• Lustre finish gold anodised to prevent corrosion.

EBC Heavy Duty Heat Treated MX Rear & ATV Front and Rear Brake Discs

• Strong heavy duty design.
• Heat treated carbon steel.
• Gold zinc anodised.
 

Find the correct fitment for your scooter or motorcycle here: EBC Brakes Fitment Guide

Indent Orders available for items not in stock or not listed.
(Air freight indents are 2 - 6 weeks delivery subject to availability)

EPFA Extreme Pro Sintered Brake Pads by EBC for trackday and fast road riding. With all the attributes of the Double-H range the EPFA Extreme Pro brake pads feature extra ingredients and vacuum furnace technology that enhances friction levels, stability and feel. Suitable for 'ride to - ride away' trackday type use. These pads are also TÜV tested and ECE R 90 approved. Another benefit is the totally silent braking ability.

Features:

• Superbike, street and trackday pad
• TÜV and ECE R 90 approved
• Ultra high brake effect and lifetime
• Perfect braking wet or dry
• Expertly crafted from the highest grade materials
• Will deliver years of reliable service
• Made to withstand the harshest conditions

Find the correct fitment for your motorcycle here: EBC Brakes Fitment Guide

Ultra lightweight EBC X series floating front rotors for sportbikes and road racers. Also available in an XC version, featuring a contoured profile rotor blades for weight reduction.

The steel used in the EBC rotor blades is also a special stainless blend with higher friction effect than normal heat treated stainless steel found on stock discs and boasts up to 10% improvement in friction effect improving brakes even further.

Weight of the X and XC series is then reduced by another 5-10% by using a 6 only button drive system on a lightweight alloy centre hub, which once again grabs the lead over stock parts.

This cannot be switched to the lighter 6 button system on alloy hubs because they are still stuck in a rut using circular rivets. Circular rivets demand more contact points to get the same geometric centralisation and still avoid generating slack in the drive direction because, being circles inside circles they only offer point contact.The SD system employs LINE contact and as such rotor blades are much more positively retained about the centre hub and never go slack in the drive direction even after abuse.

The rotors feature EBC's unique and patented S-Drive button system which features square sided rivets captured in square drive pockets on the rotor and hub which allow the outer rotor blade to expand and contract freely under the heat of braking without suffering rivet lock.

Rivet lock is the term used when rotors heat up under heavy braking and the rotor blade contacts the (normally circular) rivets that separate the inner rotor hub and the outer rotor blade. The EBC system completely eliminates this problem area which causes 100% of the failures of rotors suffering from distortion and brake vibration.
 

Find the correct fitment for your scooter or motorcycle here: EBC Brakes Fitment Guide
 

Indent Orders available for items not in stock or not listed.
(Air freight indents are 2 - 6 weeks delivery subject to availability)

Racing Pro series
This exclusive chain is developed for racing applications. Special pin-treatment, low weight and ultra low friction of the TX4 seal-rings are features that create a superior chain which will benefit you on race tracks worldwide.

Sigma XRG series
This new generation chain has been specially developed to meet the demands of today’s high-performance machines. Ultimate performance combined with a high-tech sleek appearance. Tsubaki technology and the best materials available have resulted in a product that represents the culmination of “Ultimate performance” Gold coloured outer link plates give this chain an attractive appearance and some corrosion protection.

Alpha XRG series
A third generation series, developed to meet the demand of OE-engineers for a light running, long lasting chain with high tensile strength, for current high performing machines. TX4 seal rings keep lubricant in and dirt out of the inner parts. Sleek design with gold coloured link plates distinguishes its appearance.

Omega ORS series
The Omega offers you an affordable quality sealed O-ring chain, press-fit pins with quad-stake riveting. O-ring chain with good value for the money.

Gamma series
An economical quality roller chain (solid rollers) which is suitable for less powerful bikes. The press-fit, quad-stake riveted pins add additional strength to this chain.

EBC V-Pads Semi-Sintered Brake Pads for heavy touring and cruiser motorcycles. EBC Brakes Semi-Sintered V-Pads are a new blended Semi-Sintered brake pad that combine the highest qualities of an organic brake pad with the endurance of a sintered equivalent brake pad. The Vee brake pad range are designed for the heavy cruiser/streetbike market as a replacement brake pad. The V-Pad™ range have been dyno tested and prove to be longer lasting than other cheap sintered aftermarket brake pads. All EBC Organic brake pads now incorporate backing plates which are patented with the Nucap NRS hook retention system. This guarantees zero chance of brake pad de-bonding with corrosion or extended use. EBC recommend these brake pads are not for track or race use.

Features:

• Heavy streetbike cruiser pad
• Totally ECO friendly
• Can replace organic or sintered
• TÜV and ECE R 90 approved
• Longer life organic compound
• Expertly crafted from the highest grade materials
• Will deliver years of reliable service
• Made to withstand the harshest conditions

Find the correct fitment for your motorcycle here: EBC Brakes Fitment Guide

Vee-Series Sport Bike Brake Rotors by EBC. In line with the ongoing trend for riders to customize machines rather than simply replace parts, the new Vee-Rotors from EBC Brakes offer an exciting new lightweight rotor program with an exciting range of colour options. This product is fully stainless steel heat treated and tempered back to the optimum hardness. Beware - of companies merely stating their product is stainless steel. Some of these are not hardened and of those that are, some are hardened to the excess and can exhibit cracks through over hardness between the holes and edges. EBC has worked long and hard on choosing the correct hardness and temper procedure for their brake rotors.

Features:

 • Fully floating design
 • Lightest weight rotor profile
 • Patented SD system hardware
 • Black hubs as standard
 • Various colour options
 

Find the correct fitment for your scooter or motorcycle here: EBC Brakes Fitment Guide

Indent Orders available for items not in stock or not listed.
(Air freight indents are 2 - 6 weeks delivery subject to availability)

GPFAX Sintered Road Race Brake Pads by EBC. This is a blend of brake pad that has higher friction and far better grip than any other brake product on the market. GPFAX Sintered Road Race Brake Pads have by far the highest known friction with a measurement between 0.6 and 0.7 and deliver the most amazing brake effect. Because of this factor, they are unsuitable for street use or for road tyres. Zero brake fade is guaranteed and the heat stability of these brake pads is perfect leaving the racer with high confidence and a product that can be used over numerous races. GPFAX Sintered Road Race brake pads are a closed circuit use pad only and street/highway riding with this material is highly inadvisable and dangerous. Such high friction levels as delivered by these pads are for ideal track conditions with race tyres or slicks on prepared asphalt surfaces and NOT for use with highway tires or on the highway. This material is not ECE R 90 approved nor TUV tested with a German ABE and use on the highway is therefore illegal in many countries.

Features:

• Highest performance friction level known
• Not R90 street legal or TÜV tested
• Guaranteed for lifetime performance
• Expertly crafted from the highest grade materials
• Will deliver years of reliable service
• Made to withstand the harshest conditions

Find the correct fitment for your motorcycle here: EBC Brakes Fitment Guide

Toplite’s elite performer, the AGM series, has more cranking amps and higher amp hour capacity for years of trustworthy service. Absorbed Glass Mat (AGM) batteries look different from typical powersports battery types because they are built differently. This advanced battery design eliminates water loss. Once these batteries are filled with acid, you’ll never need to fill it with water or check the acid level. This specific line is optimized to run strong without maintenance. Essentially this is the ultimate “set it and forget it” battery.

YTX(H) Series Battery Features:

• H Series – increased power, up to 30% more CCA over YTX Series
• Premium absorbed glass mat (AGM) technology
• Sealed, non-spillable design
• Meets or exceeds OEM specs
• Maintenance free – NEVER add water, but periodic charging required when not in use
• Engineered to protect against corrosion, withstand vibration, and deliver high cranking power
• Polypropylene cover and container – superior resistance in extreme conditions of cold and heat, more flexible than ABS material

TTZ Series Battery Features:

• Ideal for sport bike applications
• High CCA in a compact size
• Lightweight design
• Enhanced capacity recovery
• Expanded grid design for superior reliability
• Premium absorbed glass mat (AGM) technology
• Sealed, non-spillable design
• Meets or exceeds OEM specs
• Maintenance free – NEVER add water, but periodic charging required when not in use
• Engineered to protect against corrosion, withstand vibration, and deliver high cranking power
• Polypropylene cover and container – superior resistance in extreme conditions of cold and heat, more flexible than ABS material

Find the correct fitment for your motorcycle here: Toplite-Yuasa Fitment Guide

Simple and efficient, Toplite’s line of 12 volt 'YuMicron' high performance conventional batteries carry the unparalleled quality of any battery bearing the Toplite by Yuasa name.

Features:

• Heat sealed case protects against seepage and corrosion

• Special thin separators provides high cranking power

• Heavy-duty glass mat resists shredding of active material even under severe vibration

Find the correct fitment for your motorcycle here: Toplite-Yuasa Fitment Guide

Toplite’s elite performer, the AGM series, has more cranking amps and higher amp hour capacity for years of trustworthy service. Absorbed Glass Mat (AGM) batteries look different from typical powersports battery types because they are built differently. This advanced battery design eliminates water loss. Once these batteries are filled with acid, you’ll never need to fill it with water or check the acid level. This specific line is optimized to run strong without maintenance. Essentially this is the ultimate “set it and forget it” battery.

YT Series Battery Features:

• Premium absorbed glass mat (AGM) technology
• Sealed, non-spillable design
• Meets or exceeds OEM specs
• Maintenance free – NEVER add water, but periodic charging required when not in use
• Engineered to protect against corrosion, withstand vibration, and deliver high cranking power
• Polypropylene cover and container – superior resistance in extreme conditions of cold and heat, more flexible than ABS material

YTX Series Battery Features:

• Improved CCA over YT Series
• Premium absorbed glass mat (AGM) technology
• Sealed, non-spillable design
• Meets or exceeds OEM specs
• Maintenance free – NEVER add water, but periodic charging required when not in use
• Engineered to protect against corrosion, withstand vibration, and deliver high cranking power
• Polypropylene cover and container – superior resistance in extreme conditions of cold and heat, more flexible than ABS material

Find the correct fitment for your motorcycle here: Toplite-Yuasa Fitment Guide

Simple and efficient, Toplite’s line of 12 volt conventional batteries carry the unparalleled quality of any battery bearing the Toplite by Yuasa name.

Features:

• Special thin separators which provide high cranking power

• Engineered to protect against corrosion, withstand vibration, and deliver high cranking power

Find the correct fitment for your motorcycle here: Toplite-Yuasa Fitment Guide

Our BF307+ high performance Super DOT 4 brake fluid has been specially formulated to provide outstanding performance for braking systems routinely operated at extreme temperatures making this fluid ideal for fast street use, track days and racing. Do not mix BF307+ brake fluid with other brake fluids or its high performance may be compromised.

Typical dry boiling point – 310°C (590°F). Typical wet boiling point – 204°C (399°F)

NOT SUITABLE FOR USE WITH MINERAL OIL SYSTEMS. If in doubt consult vehicle handbook.

EBC DOT 4 brake fluid is a high quality brake fluid recommended for use in the hydraulic brake and clutch systems of all motorcycles and cars for which a glycol based DOT 3 or DOT 4 fluid is specified. With a higher boiling point than DOT 3 fluid, this fluid is ideally suited for higher performance vehicles where the braking system routinely reaches moderate brake temperatures.

Typical dry boiling point – 270°C (518°F). Typical wet boiling point – 170°C (338°F)

NOT SUITABLE FOR USE WITH MINERAL OIL SYSTEMS. If in doubt consult vehicle handbook.

EBC DOT 5 silicone brake fluid is a very high specification fluid based on polydimethylsiloxanes (silicones) and offers many advantages over conventional glycol based fluids. Silicone fluid does not absorb water from the surrounding atmosphere while in service and therefore offers greatly extended service life whilst improving corrosion resistance of the main components of the braking system.

Recommended for use in the hydraulic brake and clutch systems of all motorcycles and cars for which non-petroleum based fluid is specified. Particularly recommended for classic cars or vehicles that are garaged for much of their life but must be usable at short notice.

This fluid must only ever be mixed with DOT 5 fluid which has the same silicone base. Never mix DOT 5 with regular glycol based fluids.

Typical dry boiling point – 300°C (572°F). Typical wet boiling point – 180°C (356°F)

With the new manufacturing improvements made in 2017, we now have a strong, light chain, with sealed self lubrication that allows the chain to be constantly lubricated between the sleeve and the pin and that satisfies all demands, providing long life under all conditions for on and off road use. Excellent value for money chain.

The new O-shaped seals allow the grease to remain between the sleeve and the pin, improving the lubrication of the chain, enabling it to last for longer. The optimum life of the chain is significantly increased with respect to chains without seals.

Manufactured with high alloy steel, closed rollers and sleeve to improve resistance to fatigue. Specially treated pins to obtain greater resistance. All chains are pre-stressed to increase resistance to fatigue and elongation.

Constant technical updating to guarantee the highest level of wear resistance under any situation.

The Omega offers you an affordable quality sealed O-ring chain, press-fit pins with quad-stake riveting. O-ring chain with good value for the money!

Available in a range of pitches and lengths.

530 Omega Chain - Average Tensile Strength 39kN, Rated for 100HP

Tsubaki's Alpha ORS series is injected with a high viscosity vacuum grease during the manufacturing process, thereby improving the heat dissipation and substantially reduces the mechanical stresses. The presence of low friction O-rings limit the power losses through friction and increases longevity significantly

Available in a range of pitches and lengths.

428 Alpha ORS Chain - Rated for 65HP

Key features of this chain are a long lasting performance with low maintenance. This chain benefits from the TX4-seal rings and life-time lubrication of inner parts. Executed in a sleek designed plain steel version.

Available in a range of pitches and lengths.

428 Alpha XRS Chain - Average Tensile Strength 27kN, Rated for 80HP

A third generation series, developed to meet the demand of OE-engineers for a light running, long lasting chain with high tensile strength, for current high performing machines. TX4 seal rings keep lubricant in and dirt out of the inner parts. Sleek design with gold coloured link plates distinguishes its appearance.

Available in a range of pitches and lengths.

525 Alpha XRG Chain - Average Tensile Strength 38kN, Rated for 135HP

Our RQR series is developed exclusively for racing purposes. This chain has been used on factory bikes in the World Superbike Championships and is a proven Isle of Man TT winner.

• The choice of teams and riders in the world's leading championships
• Very rigid and high tensile strength, yet lightweight chain
• Pre-stretched to minimize elongation after first adjustment
• Available exclusively in size 520 x 120

Clip (Conn) type link for Tsubaki Gamma 520 Chain.

Clip (Conn) type link for Tsubaki Alpha O-Ring 428 Chain.

Rivet (Pin) type link for IRIS BO 520 Chain.

Rivet (Pin) type link for IRIS FB-Ring 520 Chain.

The FB’RING motorcycle chain from Iris Chains is a Super Reinforced ring seal chain, ready to withstand all types of situations. It is especially designed for sport and sport touring applications.

The Multi-lip self-lubricating seal rings with Teflon grease of the FB’RING chain, along with the high precision link stamping make this chain a high quality product. The chain is manufactured in 42CrMo4 steel alloy.

Inner link in steel, rollers and outer link in the colour gold.

Rivet (Pin) type link for IRIS BO 525 Chain.

Rivet (Pin) type link for IRIS FB 525 Chain.

Dot 4 LV is a brake fluid engineered to operate exceptionally well at low temperatures (max. cSt @ -40°C). This allows this particular fluid to be well-suited to vehicles fitted with ESP/ASR (Electronic Stability Program) systems. Dot 4 LV is designed to be used in the hydraulic brake and clutch systems of cars, commercial vehicles, and motorcycles requiring a glycol-based Dot 3 or 4 brake fluid. It can be mixed with other glycol-based brake fluids without issue.

Typical dry boiling point – 266°C. Typical wet boiling point – 173°C.

Tsubakimoto Chain co, Japan: the world's largest chain maker.

Tsubaki is produced according to the highest Japanese manufacturing standards. These high quality standards ensure a product which will guarantee maximum performance under all riding conditions.

Tsubaki's Alpha ORS series is injected with a high viscosity vacuum grease during the manufacturing process, thereby improving the heat dissipation and substantially reduces the mechanical stresses. The presence of low friction O-rings limit the power losses through friction and increases longevity significantly

Available in a range of pitches and lengths.

428 Alpha ORS Chain - Rated for 65HP

Tsubakimoto Chain co, Japan: the world's largest chain maker.

Tsubaki is produced according to the highest Japanese manufacturing standards. These high quality standards ensure a product which will guarantee maximum performance under all riding conditions.

Key features of this chain are a long lasting performance with low maintenance. This chain benefits from the TX4-seal rings and life-time lubrication of inner parts. Executed in a sleek designed plain steel version.

Available in a range of pitches and lengths.

428 Alpha XRS Chain - Average Tensile Strength 27kN, Rated for 80HP

Tsubakimoto Chain co, Japan: the world's largest chain maker.

Tsubaki is produced according to the highest Japanese manufacturing standards. These high quality standards ensure a product which will guarantee maximum performance under all riding conditions.

Key features of this chain are a long lasting performance with low maintenance. This chain benefits from the TX4-seal rings and life-time lubrication of inner parts. Executed in a sleek designed plain steel version.

Available in a range of pitches and lengths.

428 Alpha XRS Chain - Average Tensile Strength 27kN, Rated for 80HP

The BT02 is a battery & alternator tester designed to save time on electrical issues, it gives a instant diagnosis.

With all the features inside an automatic, you cannot use it wrong.

FEATURES

• For 12V battery
• Test the condition of your battery and alternator
• Connect the crocodile clip to battery terminal and check alternator or battery
• Easy to use

INSTRUCTIONS

1. Connect the red crocodile clip to the positive (+) battery terminal
2. Connect the black crocodile clip to the negative (-) battery terminal

Battery Check

• Switch on the vehicle lights for 1-2 minutes
• Disconnect the battery from the vehicle
• Wait 10 minutes
• Connect the tester

Alternator Check

• Run the vehicle with all electrical equipment off (lights, radio...)
• Run the vehicle with all electrical equipment on (lights, radio...)
• The green LED should light on both tests meaning the alternator is GOOD
• A red LED indicates the alternator is over charging : must be controlled
• No LED light indicates the alternator may not be charging : must be controlled

BTX14 battery is a part of our SLA range. Designed to make the user life easier, this 12V 12.6Ah battery is ready to use, 100% maintenance free and completely spill proof.

Extremely simple to install & carry, this BTX14 battery offers increased power, extended life and maximum reliability to all powersport vehicles that require high performance.

Cross Reference:

• Yuasa / Top Lite / Katana: YTX14-BS
• Motobatt: MBTX12U / MBYZ16H
• Powerroad: YG14-BS
• USPS: USX14-BS

Specifications:

• Technology: SLA
• Voltage (V): 12
• Capacity 10hr (Ah): 12
• Capacity 20hr (Ah): 12.6
• CCA (A): 200
• Polartiy:
• Terminal:
• Dimensions (mm): 150 x 87 x 145

Features:

• Wet charged factory activated and ready to go
• Higher life cycle (up to three times longer than conventional batteries)
• Easy to install (no risk of spilling acid)
• Plate sulfation minimized
• AGM construction (absorbed acid)
• VRLA battery (Valve Regulated Lead Acid)
• Sealed, no gas emission through venting hole (under normal operation)
• Increased power and extended life
• Extreme vibration resistance

Find the correct fitment for your motorcycle here: BS Battery Fitment Guide

BSLi-10 battery is a part of our LiFePO4 range. Designed for the most demanding riders, this 12.8V 7.5Ah (90Wh) battery offers maximum starting performance, further safety and higher cycle life. With its ultra-lightweight design, this BSLi-10 battery provides faster acceleration to all powersport vehicles.

Useful, this battery is equipped with a voltage indicator to check the state of charge at any time.

Replacement Conversion from BS Batteriers SLA:

BTX20L, BTX20HL, BTX24HL, SLA12-19, BTX20L-BS, BTX20HL-BS, BTX24HL-BS, SLA12-19-BS, B50-N18L-A/A2/A3/AT, 51913

Specifications:

• Part Number: 360118
• Technology: LiFePO4
• Voltage (V): 12.8
• Capacity 10hr (Ah): 7.5
• Power (Wh): 90
• CCA (A): 480
• Polartiy:
• Terminal:
• Dimensions (mm): 148 x 86 x 105

FEATURES

• Ready to use
• Lighter weight – up to 70% than lead acid batteries
• Multi-positioning mounting – up to 180°
• Extensive cycle life – over 2000 cycles
• Fast charging
• Very safe and environmental friendly
• Very low self discharge
• Can start engines after a long period of storage
• Robust brass terminals
• Heat temperature resistance up to 230 °C
• Waterproof design
• Spacers to adjust the dimensions if necessary, to make sure new battery can be installed firmly in the battery box

UPGRADE FROM:

Find the correct fitment for your motorcycle here: BS Battery Fitment Guide

1" O.D, Smooth for custom applications - these have no slots, dimples or castellated ends. We have TBW versions available also.

Refer to diagram for dimensions.

The top-selling handlebar in our range, and for good reason. Our Tracker bars come in two O.D.'s and three heights, and look great in any stock or aftermarket riser you can imagine. These handlebars are constructed with seamless CNC mandrel bent 0.120” wall 4130 chromoly tubes. Available in two styles: Smooth bars are for custom applications and have no slots, dimples or castellated ends. TBW w/ insert handlebars work with regular, cable-operated throttles, and if you remove the black end plug it will accept Harley's Throttle-By-Wire control module. These bars have slots on each side for stock H-D hand controls and an exit slot in the center for internal wiring.

Features:

• Seamless 0.120" (3mm) wall 4130 chromoly construction
• Precision mandrel-bent tubing for comfortable, precise ergonomics
• Black electroplate finish
• 1" O.D (7/8" option available), 18.4mm I.D
• 1" O.D. model available in smooth for custom application or TBW w/ insert for regular, cable-operated throttles, and if you remove the black end plug it will accept Harley's Throttle-By-Wire control module
• Technischer Überwachungsverein (Technical Inspection Association, or TüV) in Germany is an independent laboratory that tests the fatigue strength, manufacturing quality, and fitment for a wide range of consumer products, with special emphasis on automotive and motorcycle components and accessories. Biltwell handlebars and risers that have received TüV verification are among the strongest and most thoroughly well-tested motorcycle parts in the world.

Form & Function:

With a backsweep less severe than most stock handlebars, any Tracker in our range is a great replacement for riders who want to ditch the wheelbarrow feel of OE bars. When people ask for our advice on which Tracker to mate with any given Murdock riser, we recommend building a combo that puts your hands slightly below or even with the height of your shoulders when you're sitting comfortably on your motorcycle. Hands higher than shoulder height is popular, but it's a position better suited for experienced riders. If the cables and control wires on your bike prohibit going too tall or wide with your bars, combine our low or mid Tracker with some Slimline or Thunder risers for a clean, race-inspired, comfortable cockpit.